Menu items in the range 300 to 399, relating to editing operations (Continued)

Item number

Item name

 

Settings

 

 

 

 

 

 

 

 

 

334

EE REFERENCE

 

Specify how to select the reference video signal in E-E mode.

 

 

CONTROL

 

NORMAL

: Select according to the table in Section 3-2-1 “Selecting Reference

 

 

 

 

Signal

Depending on Operational Status” (page 3-2).

 

 

 

 

INPUT: In E-E mode select the input video signal. When not in E-E mode, select

 

 

 

 

according to the table in Section 3-2-1 “Selecting Reference Signal Depending

 

 

 

 

on Operational Status” (page 3-2).

 

 

 

 

 

 

 

 

 

336

EDIT PRESET INHIBIT IN

 

Specify which buttons are disabled in the editing mode setting section on the

 

 

KEY PANEL CONTROL

 

lower control panel.

 

 

 

 

OFF

: Disable no buttons.

 

 

 

 

TC:

Disable the TC button.

 

337

EXTERNAL REFERENCE

 

Select the signal used when this unit is set up by setup menu item 309 and

 

 

SELECT

 

F2(OUTREF) in function menu page 4 to use an external reference video signal.

 

 

 

 

HD

: Use a high definition reference video signal. Input a three-valued (positive

 

 

 

 

and negative) sync signal to the REF.VIDEO INPUT connector.

 

 

 

 

SD : Use a reference video signal. Input a video signal with chroma burst (VBS)

 

 

 

 

or a monochrome video signal (VS) to the REF.VIDEO INPUT connector.

 

 

 

 

 

 

 

338

OUTPUT AUDIO/TC

 

Set the audio (AES/EBU and analog) and time code output phase.

 

 

PHASE

 

HD

: Sync with HDSDI output phase.

 

 

 

 

SD

: Sync with SD output phase.

 

 

 

 

 

 

 

 

 

 

Menu items in the range 400 to 499, relating to preroll

 

 

 

 

 

 

 

 

 

 

 

Item number

Item name

 

Settings

 

 

 

 

 

 

 

 

 

 

 

 

401

FUNCTION MODE

 

Select the state that the unit goes into after a cuing-up operation.

 

 

AFTER CUEUP

 

STOP

: Stop (the “stop mode”)

 

 

 

 

STILL: Still playback (in search mode)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note

 

 

 

 

 

 

When controlling this unit from an editor with the standard constants set, select

 

 

 

 

“STOP”.

 

 

 

 

 

 

 

 

 

 

 

 

 

402

TIME REFERENCE FOR

 

When prerolling a tape with time code discontinuities, select whether or not to use

 

 

PREROLL

 

CTL pulses to count time code from before a discontinuity.

 

 

 

 

CTL

: Use CTL pulses to count time code.

 

 

 

 

TC: Do not use CTL pulses to count time code.

 

 

 

 

 

 

 

 

 

 

403

AUTOMATIC PREROLL

 

Select whether or not the edit IN point is automatically set by pressing the

 

 

REFERENCE ENTRY

 

PREROLL button, when the IN point is not set before starting preroll.

 

 

 

 

DIS

: IN point is not set automatically.

 

 

 

 

ENA: IN point is set automatically.

 

 

 

 

 

 

 

 

 

405

CUEUP BY CTL

 

Select the tape transport mode when cuing. This setting is valid only when the

 

 

 

 

function menu item CTL/TC is set to CTL.

 

 

 

 

CAP.

: During cuing up, the tape transport is in the “pinch ON” state (maximum

 

 

 

 

tape speed 10 times normal).

 

 

 

 

REEL : During cuing up, the tape transport is in the “pinch OFF” state. As the

 

 

 

 

tape approaches the cue up point and the tape speed drops, the tape transport

 

 

 

 

 

 

 

 

 

 

 

 

 

switches to the “pinch ON” state.a)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To give priority to editing accuracy, select “CAP”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

a) When controlled from an editor (BVE-2000/9100 etc.),

 

 

 

 

 

 

 

 

 

 

 

 

10Chapter

selecting “REEL” allows high-speed cuing up.

 

 

 

 

 

 

 

 

 

 

 

 

MenusSetup

Chapter 10 Setup Menus 10-17