|
|
|
|
| To change the display while | |
|
|
|
| |||
|
|
|
|
| recording | |
Recording to an MD | ||||||
| Press LEVEL/DISPLAY/CHAR (or DISPLAY) | |||||
|
|
|
|
| ||
If the MD has been partially recorded, |
| repeatedly to change the display. | ||||
|
| |||||
recording starts after the recorded tracks. |
| Each time you press the button, the display | ||||
1 Turn on the amplifier and program |
| |||||
| changes cyclically as follows: | |||||
source, and select the source on the |
| Track number and recorded time of the current | ||||
amplifier. |
|
|
| |||
|
|
| track tRemaining recordable time2) on the | |||
2 Press ?/1 to turn on the deck. |
| |||||
| MD tLevel of the input signal tTrack | |||||
The STANDBY indicator turns off. |
| name3) | ||||
3 Load a recordable MD into the slot |
| 2) Time shown in the display differs depending on | ||||
|
|
| the setting of REC MODE. | |||
|
|
| 3) “No Name” appears when the track has no name. | |||
4 Press INPUT repeatedly to select the |
| |||||
|
| |||||
input jacks (connector) connected to |
|
| ||||
| Notes on recording | |||||
the program source. |
|
| ||||
| When the source is |
| Set INPUT to |
| After recording | |
| connected to the |
|
|
| ||
|
|
|
| Press EJECT Ato remove the MD or press | ||
| DIGITAL OPTICAL IN |
| ||||
| connector |
|
|
| ?/1to turn off the deck. | |
| ANALOG IN jacks |
|
| “TOC” or “TOC Writing” starts flashing. The | ||
|
|
|
|
| TOC is updated and recording is completed. | |
5 Press REC z. |
|
| ||||
|
|
| Before disconnecting the AC power | |||
The deck changes to recording pause. |
| |||||
6 Adjust the recording level if necessary. |
| cord | ||||
| MD recording is completed when the MD Table | |||||
For details, see “Adjusting the recording |
| |||||
| of Contents (TOC) is updated. The TOC is | |||||
|
|
| ||||
|
|
| updated when you eject the MD or press ?/1to | |||
7 Press Hor X. |
|
|
| |||
|
|
| turn off the deck. Do not disconnect the AC | |||
Recording starts. |
|
|
| power cord before updating the TOC (while | ||
8 Start playing the program source. |
| “TOC” is lit) or while updating the TOC (while | ||||
Operations you may want to do |
| “TOC Writing” is flashing) to ensure a | ||||
| complete recording. | |||||
during recording |
|
|
| |||
|
|
| Automatic conversion of digital | |||
|
|
|
|
| ||
To | Press |
| ||||
|
| sampling rates | ||||
|
|
|
|
| ||
Stop recording | x |
| ||||
|
| A | ||||
|
|
|
|
| ||
Pause recording | X |
| ||||
|
| converts the sampling frequency of various | ||||
|
|
|
|
| ||
Resume recording after | Hor X |
|
| digital sources to the 44.1 kHz sampling rate of | ||
pausing1) |
|
|
| the MD deck. This allows you to monitor and | ||
Eject the MD | EJECT Aafter stopping |
| record sources such as 32 or 48 kHz DAT tape | |||
|
| recording |
|
| or satellite broadcasts, as well as the CDs and | |
1) The track number increases by one. |
| MDs. |
8GB