Pin No. | Pin Name | I/O |
| Description | |||
|
|
|
| ||||
90 | SPDW | O | Spindle motor drive control signal output (W) to the motor driver | ||||
|
|
|
|
| |||
91 | DSPVDD2 | — | Power supply terminal (for DSP block) (+1.5V) |
| |||
|
|
|
|
|
| ||
92 | DSPVSS1 | — | Ground terminal (for DSP block) |
|
| ||
|
|
|
| ||||
93 | SPCU | I | Spindle motor drive comparison signal input (U) from the motor driver | ||||
94 | SPCV | I | Spindle motor drive comparison signal input (V) from the motor driver | ||||
95 | SPCW | I | Spindle motor drive comparison signal input (W) from the motor driver | ||||
|
|
|
| ||||
96 | SDU | O | Sled motor drive signal output (U) to the motor driver | ||||
|
|
|
| ||||
97 | SLVS | O | Sled servo drive PWM signal output to the motor driver | ||||
|
|
|
| ||||
98 | SDV | O | Sled motor drive signal output (V) to the motor driver | ||||
|
|
|
| ||||
99 | SDW | O | Sled motor drive signal output (W) to the motor driver | ||||
100 | SLCU | I | Sled motor drive comparison signal input (U) from the motor driver | ||||
101 | SLCV | I | Sled motor drive comparison signal input (V) from the motor driver | ||||
102 | SLCW | I | Sled motor drive comparison signal input (W) from the motor driver | ||||
|
|
|
|
| |||
103 | DIFVDD1 | — | Power supply terminal (for DSP I/F) (+1.9V) |
| |||
|
|
|
|
|
|
| |
104 | DIFVSS1 | — | Ground terminal (for DSP I/F) |
|
|
| |
|
|
|
|
| |||
105 | EFMO | O | EFM encode data output terminal for the record | Not used | |||
106 | MNT0 | O | Internal DSP monitor output (0) terminal | Not used | |||
107 | MNT1 | O | Internal DSP monitor output (1) terminal | Not used | |||
108 | MNT2 | O | Internal DSP monitor output (2) terminal | Not used | |||
|
|
|
|
| |||
109 | MNT3 | O | Internal DSP monitor output (3) terminal | Not used | |||
|
|
|
|
| |||
110 | SENSE | O | Internal DSP (SENS) monitor output terminal | Not used | |||
|
|
|
| ||||
111 | TX | O | Record data output enable signal output monitor terminal of the internal DSP Not used | ||||
|
|
|
| ||||
112 | RECP | O | Laser power changeover signal output monitor terminal Not used | ||||
113 | DSPVDD3 | — | Power supply terminal (for DSP block) (+1.5V) |
| |||
114 to | NC | O | Output terminal for the external | Not used | |||
117 | |||||||
|
|
|
|
|
| ||
|
|
|
|
|
| ||
118 | DRAMVSS0 | — | Ground terminal (for the external |
|
| ||
|
|
|
| ||||
119 | DRAMVDD0 | — | Power supply terminal (for the external | ||||
|
|
|
|
|
|
| |
120 to | NC | O | Output terminal for the external | Not used | |||
138 | |||||||
|
|
|
|
|
| ||
|
|
|
| ||||
139 | DRAMVDD1 | — | Power supply terminal (for the external | ||||
140 | DRAMVSS1 | — | Ground terminal (for the external |
|
| ||
141 | TSB MST VDD | — | Power supply terminal (for TSB master communication) (+1.9V) | ||||
|
|
|
| ||||
142 | RMC DTCK | I/O | TSB serial data input/output with the remote commander attached headphone | ||||
|
|
|
| ||||
143 | TSB SLV VDD | — | Power supply terminal (for I/F to TSB slave communication) (+1.9V) | ||||
|
|
|
|
|
|
| |
144 | TSB SLVI | I | TSB slave signal input terminal | Not used |
|
| |
|
|
|
|
| |||
145 | TSB SLVO | O | TSB slave signal output terminal Not used |
| |||
146 | TDI | I | Data input terminal for JTAG | Not used |
|
| |
147 | TMS | I | Test mode control input terminal for JTAG | Not used | |||
|
|
|
|
|
|
| |
148 | TCK | I | Clock input terminal for JTAG | Not used |
|
| |
|
|
|
|
|
|
| |
149 | XTRST | I | Reset input terminal for JTAG | Not used |
|
| |
|
|
|
|
|
|
| |
150 | TDO | O | Data output terminal for JTAG | Not used |
|
| |
|
|
|
|
|
| ||
151 | JTAGVDD | — | Power supply terminal (for JTAG) (+2.3V) |
|
| ||
152 | JTAGVSS | — | Ground terminal (for JTAG) |
|
|
| |
153 | MCUVDD2 | — | Power supply terminal (for the microcomputer block) (+1.5V) | ||||
|
|
|
| ||||
154 | MIFVDD0 | — | Power supply terminal (for the microcomputer I/F block) (+1.9V) | ||||
|
|
|
| ||||
155 | MIFVSS0 | — | Ground terminal (for the microcomputer I/F block) | ||||
|
|
|
|
|
|
| |
37
