Lower surface of the disc

Write Inhibit tab

 

 

 

 

Slide in the direction of the arrow

 

Write Inhibit tab settings

 

 

 

 

 

SAVE

 

 

SAVE

 

 

 

 

 

 

 

 

 

 

 

3 Chapter

Recording enabled

Recording disabled

You can also write protect individual clips. For details, see

andRecording

“Locking (Write-Protecting) Clips” (page 59).

 

Playback

Loading and Unloading a Disc

When the on/standby switch indicator is lit green, you can

 

load and unload a disc as shown in the following figure.

On/standby switch and indicator

To unload

Press the EJECT button.

To load

Insert a disc face up.

The disc is drawn in.

The disc slot indicator flashes orange when you insert a disc, and lights blue when the disc is completely loaded. The indicator flashes blue when you eject a disc, and goes out when the disc is completely ejected.

Formatting a Disc

Unused discs are formatted automatically when they are loaded into this unit.

To format a recorded disc, load the disc into the unit, then proceed as follows.

Note

When a recorded disc is formatted, all the data on the disc is erased. (Locked clips (see page 59) are also erased.)

 

 

 

 

 

 

1

 

2,73,4,5

 

 

 

 

 

 

 

 

 

 

 

 

 

EJECT

 

 

 

 

 

F1

 

 

 

 

 

 

 

 

 

 

 

 

 

F2

 

 

 

 

 

 

 

 

ACCESS

 

 

 

 

F3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NETWORK

 

 

 

 

F4

 

 

 

MENU

 

MARK1

 

VAR

 

 

 

 

 

CHAPTER

 

 

 

 

 

 

 

LOCAL

 

 

 

 

 

 

 

 

 

 

 

 

 

REMOTE

 

 

 

 

F5

EXPAND

SUB

THUMB

 

 

IN

OUT

 

 

 

 

 

SET

RESET

 

 

JOG

LEVEL

 

 

 

 

 

 

CLIP

NAIL

 

 

 

 

 

 

PAGE DISPLAY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLIP

ESSENCE

 

 

 

 

 

 

 

 

 

 

 

 

MENU

MARK

 

 

MARK2

 

 

PHONES

CH 1

CH 2

CH 3

CH 4

 

KEY INHI

PREV

PLAY

NEXT

STOP

REC

SHUTTLE

VARIABLE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REC

 

 

 

 

 

 

 

 

 

 

 

 

 

PRESET

 

 

 

 

 

 

 

 

 

 

 

 

 

PB

SHIFT

 

 

 

 

 

 

 

 

 

 

 

 

 

TOP

F REV

F FWD END

STANDBY

 

 

 

 

 

 

 

 

 

 

 

6

1 Press the DISPLAY button to maximize the monitor video section.

2 Press the MENU button.

The system menu appears on the display.

3 Select “DISC MENU” using the M/MARK1 button or m/MARK2 button, then press the ,/OUT button.

4 Select “FORMAT” using the m/MARK2 button, then press the ,/OUT button.

The menu item QUICK FORMAT is selected.

5 Press the ,/OUT button.

The message “QUICK FORMAT OK?” appears.

To cancel a disc format

Press the RESET button to return to the state of step 3. To clear the menu from the screen, carry out step 7.

6 Press the SET button.

The format starts.

The message “FORMAT COMPLETED.” appears when formatting of the disc is completed.

If you want to continue by formatting another disc When the message “FORMAT COMPLETED.” appears, press the EJECT button to eject the disc. Insert the next disc to format, and press the SET button when the message “QUICK FORMAT OK?” appears.

7 Press the MENU button to clear the menu from the screen.

44 Handling Discs