•This unit’s S400 connector has 6 pins. Check the number of pins on the i.LINK connector of your notebook computer, and use an appropriate i.LINK cable.

See “Using PDZ-1 Proxy Browsing Software” in Chapter 4 (page 79) for more information about installing the PDZ-1 software. See the online help of PDZ-1 for more information about using PDZ-1.

 

Some limitations apply to FAM connections. For details,

2Chapter

see “File Operations in File Access Mode (for Windows)”

in Chapter 5 (page 83).

 

 

Preparations

 

 

 

 

 

 

 

PDW-F75 (this unit)

 

 

 

 

 

 

 

REF VIDEO INPUT

COMPOSITE OUTPUT

AUDIO MONITOR

TIME CODE

-AC IN

 

 

 

 

R

L

IN OUT

POWER

 

 

 

 

 

 

 

 

 

 

 

 

 

ANALOG HD INPUT

 

 

 

 

 

 

Y/G

PB /R

 

 

AUDIO INPUT

 

AUDIO OUTPUT

DIGITAL 1/2

3/4

 

 

1/3

2/4

1/3

2/4

AUDIO

 

 

 

(AES/EBU)

PB /B

SYNS

 

 

 

 

 

INPUT

 

 

 

 

 

 

 

1/2

3/4

 

 

 

 

 

 

OUTPUT

 

 

 

HDSDI INPUT

HDSDI OUTPUT SDSDI OUTPUT

 

 

 

 

 

1

2

 

MONITOR

RS232C

REMOTE(9P)

 

 

 

 

 

 

 

 

 

 

CONTROL

 

S400

 

 

 

 

 

 

 

S400

i.LINK cable (not supplied)

i.LINK (IEEE1394) connector

Laptop computer

On the computer

On this unit

Install PDZ-1.

Set the setup menu item

 

INTERFACE SELECT

 

>REMOTE I/F to “i.LINK” (see

 

page 103).

 

Set the setup menu item

 

INTERFACE SELECT >i.LINK

 

MODE to “FAM(PC REMOTE)”

 

(see page 103).

 

 

Connecting to a Nonlinear Editing System (AV/C Connection)

You can send video/audio signals (AV/C data) from this unit to a nonlinear editing system connected to the S400 connector.

The following figure shows an example connection.

See “Using PDZ-1 over an i.LINK Connection (FAM Connection)” (page 29) for the connections and settings to make a FAM connection between this unit and a nonlinear editing system.

Notes

•The S400 connector of this unit outputs video/audio signals in DVCAM format. Data recorded in MPEG HD format is output after being converted into DVCAM format.

•The nonlinear editing system to be connected to this unit requires editing software (not supplied) supporting the DVCAM format.

•To transfer video and audio signals (AV/C data), use AUDIO CONTROL >DV OUT MODE (see page 102) in the setup menu to select the audio mode (the factory default is “2ch”).

•This unit’s S400 connector has 6 pins. Check the number of pins on the i.LINK connector of your laptop computer, and use an appropriate i.LINK cable.

 

 

 

 

 

 

 

 

PDW-F75(this unit)

REF VIDEO INPUT

COMPOSITE OUTPUT

AUDIO MONITOR

TIME

CODE

-AC IN

 

 

 

 

R

L

IN

OUT

POWER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ANALOG HD INPUT

 

 

 

 

 

 

 

Y/G

PB /R

 

AUDIO INPUT

 

 

AUDIO OUTPUT

DIGITAL 1/2

 

3/4

 

1/3

2/4

 

1/3

2/4

AUDIO

 

 

 

 

(AES/EBU)

 

PB /B

SYNS

 

 

 

 

 

INPUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1/2

 

3/4

 

 

 

 

 

 

OUTPUT

 

 

 

HDSDI INPUT

HDSDI OUTPUT

SDSDI OUTPUT

 

 

 

 

 

1

2

 

 

MONITOR

 

RS232C

REMOTE(9P)

 

 

 

 

 

 

 

 

 

 

 

CONTROL

 

 

S400

 

 

 

 

 

 

 

 

S400

i.LINK cable (not supplied)

i.LINK (IEEE1394) connector Laptop computer

On the computer

On this unit

Install editing software

Set the setup menu item

supporting the DVCAM

INTERFACE SELECT

format.

>REMOTE I/F to “i.LINK” (see

 

page 103).

 

Set the setup menu item

 

INTERFACE SELECT >i.LINK

 

MODE to “AV/C” (see page

 

103).

Connections for Cut Editing

By connecting this unit to a VTR, you can configure a cut editing system. Some example connections are shown in the following.

Note

This unit cannot be used as a recorder for linear editing. When it receives an assemble command, this unit starts normal recording operation and creates a new clip.

30 Connections and Settings