Sony UP-970AD manual 16

Menu List

Item Function Settings

Mode Analog

This section describes the menus displayed as you turn the jog dial. The setting surrounded by indicates the factory setting.

Item	Function	Settings
AGC	To adjust the	AG:ON: Adjusts the input
	input signal to the	signal to the optimum level,
	optimum printing	when the printout image
	level	appears too dark or too
		light.
		[AG:OFF]: Normally select
		this setting.
		BACK: Cancels the setting
		change and returns to the

FEED	To set the top and
(UP-990AD)	bottom margin of
	a print.

[FE: 0]to FE:15: Sets the margin to one of 16 steps from 0 to 15. An increase of one step increases the top and bottom margin by 5

mm.The top and bottom margin can be increased to 75 mm. The “0” setting is the default value, which still provides a narrow margin between two images.

BACK: Cancels the setting change and returns to the item selection column.

		item selection column.
ASPCT a)	To select the	AS:1:1: Prints a video
	aspect ratio	signal with an aspect ratio
		of 1:1.
		[AS: 4:3]: Normally select
		this setting.
		BACK: Cancels the setting
		change and returns to the
		item selection column
BEEP	To turn operation	BE: OFF: The operation
	tones ON and	tone does not sound.
	OFF. Error tones	[BE: ON]: The operation
	sound regardless	sounds.
	of setting.	BACK: Cancels the setting
		change and returns to the
		item selection column.
CLEAN	To start head	[CLN: OK]: Starts the head
	cleaning	cleaning. Be sure to use the
		supplied cleaning sheet.
		BACK: Cancels the head
		cleaning and returns to the
		item selection column.
CLEAR	To delete images	[CLR: OK]: Deletes all
	stored in memory.	images stored in memory.
		BACK: Cancels CLEAR
		and returns to the item
		selection column.
AT.CUT	To turn on and off	CT:OFF: Cuts the paper
(UP-990AD	automatic cutting	when the CUT button is
only function)	of completed	pressed.
	prints.	[CT:ON]: Cuts the paper
		automatically.
		BACK: Cancels the setting
		change and returns to the
		item selection column.
DIR b)	To select whether	DI: REV: Starts to print in
	the top or bottom	the reverse direction (from
	of the screen is to	the top of the screen).
	be printed first	[DI: NOR]: Starts to print in
		the normal direction (from
		the bottom of the screen).
		BACK: Cancels the setting
		change and returns to the
		item selection column.

FEED	To select the	[FE: ON]: Increases the
(UP-970AD)	paper feed	margin between prints.
	method used after	FE:OFF: Sets when
	printing.	reducing the margin or
		when printing multiple
		images on the same sheet.
		This reduces the margin
		between images allowing
		you to print more images
		per roll. However, with this
		setting, the FEED button
		must be pressed before
		cutting the paper.
		BACK: Cancels the setting
		change and returns to the
		item selection column.
FRAME	To select the	FR:BLK: Sets the frame
	color of the frame	color to black.
	between images	[FR:WHT]: Sets the frame
	in multi-picture	color to white.
	mode.	BACK: Cancels the setting
		change and returns to the
		item selection column.
GAMMA	To select the tone	GA:3: TONE 3 Hard
	of the printouts	gradation
	(density	GA:2: TONE 2 Soft
	gradation)	[GA:1]: TONE 1 Standard
		gradation
		BACK: Cancels the setting
		change and returns to the
		item selection column.
IMAGE	To set the printout	IM:NEG: Makes negative
	to either positive	printouts.
	printout or	[IM:POS]: Makes normal
	negative printout	printouts.
		BACK: Cancels the setting
		change and returns to the
		item selection column.
INFO	To select whether	IF:ON: Prints the
	or not the print	information.
	conditions (such	[IF:OFF]: Does not print the
	as contrast,	information.
	bright, gammas	BACK: Cancels the setting
	and sharpness	change and returns to the
	information) are	item selection column.
	printed under the
	image

16 Adjustments and Settings Using the Menu