Connecting

• insert the plugs of the cables properly; plugs that are

Connectingnot fully inserted often generate noise. When pulling out a cable, be sure to pull it out from the plug, not

Connecting with a Computer

This section describes how to connect the projector to a computer.

You can control the projector from your computer by using the application software supplied with the projector, and/or you can use USB equipment. For details, see “Using USB equipment (e.g., USB mouse)”.

When the projector is connected to a computer, you can control the mouse of a computer by the Remote Commander.

The R/L CLICK keys and joy stick function as follows.

Note

Make sure that there is nothing to obstruct the infrared beam between the Remote Commander and the remoter control detector on the projector.

the cable itself.

Notes

Connect all the connecting cables to the INPUT A connector when you input a signal from the INPUT A connector.

Connect all the cables to the INPUT B connector when you input a signal from the INPUT B connector as well.

Supplied mouse cables may not work properly according to your computer.

When connecting with an IBM PC/AT compatible computer

Setting up

and pr ojecting

Key and

Function

 

 

 

IBM PC/AT1)

Macintosh

joy stick

 

compatible, Serial

 

 

 

 

R CLICK

Right button

Mouse button

(front)

 

 

 

 

 

L CLICK

Left button

Mouse button

(rear)

 

 

 

 

Joy stick

Corresponds with the movements of the mouse

Also refer to the instruction manual of equipment to be connected.

Notes

• This unit accepts the VGA, SVGA, XGA or SXGA

signals. However, we recommend you to set the

output signal of your computer to the XGA.

• If you set your computer, such as a notebook type

IBM PC/AT compatible, to output the signal to both

the display of your computer and the external

monitor, the picture of the external monitor may not

appear properly. In such cases, set the output mode

of your computer to output the signal to only the

external monitor.

For details, refer to the operating instructions supplied

with your computer.

• The RGB input connectors of the INPUT A/B and

DIGITAL RGB connector of the INPUT A comply

with the VESA DDC2B. If your computer or

graphics board is compatible with DDC, turn on the

power of the equipment as follows:

1 Connect the projector to the computer with the HD

D-sub 15-pin cable.

 

 

 

DIGITAL

 

 

 

Right side

 

RGB

RGB

 

 

 

 

 

 

 

 

 

5BNC

 

 

REMOTE

CONTROL S

VIDEO IN

 

 

 

 

IN

 

L

R

 

RS-232C

S VIDEO

(MONO)

 

 

PLUG IN POWER

VIDEO AUDIO

 

OUTPUT

 

INPUT B

 

 

 

MONITOR

AUDIO

RGB

AUDIO

MOUSE

 

INPUT A

 

 

 

 

 

 

DIGITAL

 

 

 

 

 

RGB RGB

 

 

 

 

5BNC

RGB

AUDIO

MOUSE

 

USB

 

 

 

 

 

 

 

DIGITAL RGB

R/R-Y/PR

G/Y B/B-Y/PBSYNC/HD

VD

 

HD D-sub

 

 

 

15-pin

 

 

 

Speaker

cable

 

 

 

(supplied)

 

 

Monitor cable SMF-410 (not supplied)

 

to

to

 

monitor

audio

Monitor

out

out

Computer

to INPUT A or INPUT B

SIC-S21 (for serial)/S22 (for PS/2) Mouse cable (supplied)

Stereo audio connecting cable (not supplied)

to serial port or to mouse port

2

Turn on the power of the projector.

3

Boot up the computer.

When making connections, be sure to:

turn off all equipment before making any connections.

use the proper cables for each connection.

Note

Set the DIGITAL RGB/5BNC/RGB switch to RGB (right) when you connect the computer to the INPUT A connector.

.........................................................................................................................................................................................................

1) IBM and PC/AT are a trademark and a registered trademark of International Business Machines Corporation, U.S.A.

15 (GB)

Page 15
Image 15
Sony VPL-PX21 Connecting with a Computer, When connecting with an IBM PC/AT compatible computer, Boot up the computer