Sony VPL-VW200 48

Setup Menu

The Setup menu is used to change the factory preset settings, etc.

Status	Sets whether or not the on-screen display is displayed.
	Set to “Off” to turn off the on-screen displays except for the menus,
	message when turning off the power, and warning messages.

Language	Selects the language used in the menu and on-screen displays.
	Available languages are: English, Dutch, French, Italian, German,
	Spanish, Portuguese, Russian, Swedish, Norwegian, Japanese,
	Chinese (Simplified Chinese), Chinese (Traditional Chinese),
	Korean, Thai and Arabic.

Cooling Setting	Use this item when using the projector at high altitudes.
	High: Use this setting when using the projector at an altitude of
	1,500 m or higher.
	Standard: Use this setting when using the projector at normal
	altitudes.
	Note
	When this item is set to “High”, the fan noise becomes slightly
	louder since the number of fan rotation increases.

Standby Mode	Sets to lower the power consumption in standby.
	Standard1: Sets power consumption to normal.
	Standard2: Sets the network function ineffective and reduces power
	consumption lower than “Standard1”.
	Low: Reduces power consumption lower than “Standard2”.
	Note
	When this item is set to “Low”, the HDMI Control function and the
	network function will not operate in standby.

Power Saving	Sets the power saving mode.
	When set to “On”, the projector goes into power saving mode if no
	signal is input for 10 minutes. At that time, the ON/STANDBY
	indicator lights in orange, then the screen becomes dark. In power
	saving mode, the power saving mode is cancelled if a signal is input
	or any button is pressed. If you do not want to set the projector to
	power saving mode, select “Off”.

48

Contents

VPL-VW200 For customers in the USA Declaration of Conformity Disposal of Used Lamp For customers in Europe Trademark Information Page Table of Contents Location of Controls Connections and Preparations Projecting Others On safety On preventing internal heat buildup Caution On repacking Location of Controls Page Page Connections and Preparations Before Setting Up the Projector Improper use Do not do any of the following while using the projector Blocking the ventilation holes Tilting front/rear and left/right When installing the unit at altitudes Connecting the AC Power Cord Positioning the Projector and a screen When using the 16:9 aspect ratio screen When using the 4:3 aspect ratio screen (projecting a 4:3 picture) 2 Position the projector so that the lens is parallel to the screen Top view Connecting to a VCR Page To connect to a VCR equipped with the S video connector or video connector Connecting to a Computer 1 Plug the power plug into the wall outlet 2 Press the ?/1 (ON/STANDBY) switch to turn on the projector 3 Turn on the equipment connected to the projector 4 Press INPUT to project the picture on the screen 5 Adjust the vertical picture position 6 Adjust the picture size 7 Adjust the focus To adjust the tilt of the installation surface 1 Press MENU 2 Press M/m to select the Setup menu, and press , or 3 Press M/m to select “Language,” and press , or 4 Press M/m/</, to select a language, and press To clear the menu Projecting Turning Off the Power Press WIDE MODE Wide Zoom Normal Full Zoom Anamorphic Zoom Full1 (When the PC signal is input) Full2 (When the PC signal is input) Notes on selecting the wide screen mode Press one of the PICTURE MODE buttons (DYNAMIC, STANDARD, CINEMA and USER 1, USER 2 and USER 3) DYNAMIC STANDARD CINEMA Selecting to directly adjust the desired menu item Selecting desired adjust menu items in the order 1 Press RCP on the remote control 2 Press M/m to select “User1,” “User2” or “User3,” then press 3 Select the target color you want to adjust 4 Adjust the color of the specified portions 5 After the adjustment is complete, press Using the Menus 2 Press M/m to select a menu item, and press , or ,or 4 Make the setting or adjustment of an item Items that cannot be adjusted To reset the picture that has been adjusted To reset the items that have been adjusted Page Page Page Page Page Page Page Page Page Page Page Page Page Page About the Preset Memory No Operating the Projector from a Computer Owner and projector information Owner Projector Memo Network settings Setting passwords for “Administrator” and “User” Advanced setting To reset the setting Others Power Picture On-screendisplay Remote control Others Warning Indicators Message Lists Warning messages Caution messages Tools you need to get started: Standard Phillips screwdriver Cloth (for scratch protection) 1Turn off the projector and unplug the AC power cord 5Remove the valve cap (1), then turn the gas releasing valve clockwise, using a Philips screwdriver (2) 6Loosen the four screws on the lamp unit with a Philips screwdriver 10 Tighten the screw loosened in step 4 to close the lamp cover 11 Close the top cover 12 Reverse the projector, then 14 Remove the air filter place it on the cloth 13 Remove the filter holder 16 Attach the filter holder 18 Place the project back on its original position 20 Select “Yes” Cleaning the lens Cleaning the cabinet Black points and bright points (red, blue, or green) on the screen System Input General Supplied accessories Optional accessories Preset Signals Page Preset memory numbers for each input signal Analog signal Digital signal Input Signals and Adjustable/Setting Items Screen menu When Using the PSS-H10Projector Suspension Support When using the 4:3 aspect ratio screen Attaching the PSS-H10projector suspension support Top view Front view Side view Tools you need to get started Phillips screwdriver: 110 mm (4 3/8 inches) or longer Flat-headscrewdriver: 110 mm (4 3/8 inches) or longer When using the 16:9 screen