VPL-VW200
For customers in the USA
Declaration of Conformity
Disposal of Used Lamp
For customers in Europe
Trademark Information
Page
Table of Contents
Location of Controls
Connections and
Preparations
Projecting
Others
On safety
On preventing internal heat buildup
Caution
On repacking
Location of Controls
Page
Page
Connections and Preparations
Before Setting Up the
Projector
Improper use
Do not do any of the following while using the projector
Blocking the ventilation holes
Tilting front/rear and left/right
When installing the unit at altitudes
Connecting the AC Power Cord
Positioning the Projector and a screen
When using the 16:9 aspect ratio screen
When using the 4:3 aspect ratio screen (projecting a 4:3 picture)
2 Position the projector so that the lens is parallel to the screen
Top view
Connecting to a VCR
Page
To connect to a VCR equipped with the S video connector or video connector
Connecting to a Computer
1 Plug the power plug into the wall outlet
2 Press the ?/1 (ON/STANDBY) switch to turn on the projector
3 Turn on the equipment connected to the projector
4 Press INPUT to project the picture on the screen
5 Adjust the vertical picture position
6 Adjust the picture size
7 Adjust the focus
To adjust the tilt of the installation surface
1 Press MENU
2 Press M/m to select the Setup menu, and press , or
3 Press M/m to select “Language,” and press , or
4 Press M/m/</, to select a language, and press
To clear the menu
Projecting
Turning Off the Power
Press WIDE MODE
Wide Zoom
Normal
Full
Zoom
Anamorphic Zoom
Full1 (When the PC signal is input)
Full2 (When the PC signal is input)
Notes on selecting the wide screen mode
Press one of the PICTURE MODE buttons
(DYNAMIC, STANDARD, CINEMA and USER 1, USER 2 and USER 3)
DYNAMIC
STANDARD
CINEMA
Selecting to directly adjust the desired menu item
Selecting desired adjust menu items in the order
1 Press RCP on the remote control
2 Press M/m to select “User1,” “User2” or “User3,” then press
3 Select the target color you want to adjust
4 Adjust the color of the specified portions
5 After the adjustment is complete, press
Using the Menus
2 Press M/m to select a menu item, and press , or
,or
4 Make the setting or adjustment of an item
Items that cannot be adjusted
To reset the picture that has been adjusted
To reset the items that have been adjusted
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
About the Preset Memory No
Operating the Projector from a Computer
Owner and projector information
Owner
Projector
Memo
Network settings
Setting passwords for “Administrator” and “User”
Advanced setting
To reset the setting
Others
Power
Picture
On-screendisplay
Remote control
Others
Warning Indicators
Message Lists
Warning messages
Caution messages
Tools you need to get started:
Standard Phillips screwdriver
Cloth (for scratch protection)
1Turn off the projector and unplug the AC power cord
5Remove the valve cap (1), then turn the gas releasing valve
clockwise, using a Philips screwdriver (2)
6Loosen the four screws on the lamp unit with a Philips screwdriver
10 Tighten the screw loosened in step 4 to close the lamp cover
11 Close the top cover
12 Reverse the projector, then
14 Remove the air filter
place it on the cloth
13 Remove the filter holder
16 Attach the filter holder
18 Place the project back on its original position
20 Select “Yes”
Cleaning the lens
Cleaning the cabinet
Black points and bright points (red, blue, or green) on the screen
System
Input
General
Supplied accessories
Optional accessories
Preset Signals
Page
Preset memory numbers for each input signal
Analog signal
Digital signal
Input Signals and Adjustable/Setting Items
Screen menu
When Using the PSS-H10Projector Suspension Support
When using the 4:3 aspect ratio screen
Attaching the PSS-H10projector suspension support
Top view
Front view
Side view
Tools you need to get started
Phillips screwdriver: 110 mm (4 3/8 inches) or longer
Flat-headscrewdriver: 110 mm (4 3/8 inches) or longer
When using the 16:9 screen