SET
CHARGE
SNOOZE 12
PAGE
ALARM SPEAKER

RingerControl

Ifyou do not want the handset and basetoring , set the RINGER switch on thebackof the base unit to OFF and/or pressthe" VOL/RING " button on handset for2seconds to toggle the ringer to off. TheLCDwill show.Thehandset and/or base unit will no longerringwhen a call comes in.
-RINGERSWITCH- -RINGSOUND-
BASE HANDSET BASE HANDSET
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
HANDSET
OFF
CRADLE
HANDSET
ON
CRADLE
TelephoneOperation (Cont.)

SpeakerphoneVolume Cont rol

Youcan send a page signal from the basetothe handset.

Page/HandsetLocator

#
CH
REDIALVOL/RING
12
ABC
3
DEF
0
OPER
CALLSDEL
TALK
MEMFLASH
7
PQRS
8
TUV
9
WXYZ
4
GHI
5
JKL
6
MNO
#
CH
REDIAL VOL/RING
0OPER
Pressthe VOLUME control " "or" "buttonon the base to adjust the speakerphonevolumelevel.LED STATUS INDICATIONS-NewCaller ID information is inmemory.-Allnew Caller ID information hasalreadybeen revie wed.FLASHINGOFFNEWCALLLED

LCD/LED INDICATIONS(HANDSET)

TelephoneOperation (Cont.)
LCD DISPLAY INDICATIONS
BATTERYLOW Handsetbattery power is low, and the
handsetbattery should be charged.
PAGING Baseunit is paging handset.
TALK Handsetis connected to line.
LINEIN USE Speakerphoneactive.
Powerfailure
protection/BatteryBackup
ToReset Unit
IMPORTANT
IfDC power failure occurs, or the power plug comes out of the wall,yourunit will shut down until the power is restored.Whenthe power is restored, clock and alarm time and memory settingsrecordedbefore the power failure will be saved IF YOU HAVEINSTALLEDA 9 VOLTBATTERY.Ifyour unit is not operating properly when the power is restored, proceedwitha unit reset.1.Unplug the DC adaptor from the power outlet.2.Remove the 9 volt battery. Replace with a fresh 9 volt battery (see page 9).3.Plug DC adaptor back into power outlet.4.Set clock and alarm time, radio memory station (see page 21).5.Remove the handset battery, wait 5 seconds, and then reinstall the handset battery.Youneed to follow the Caller ID setup procedure.Duringa power outage, your unit will NOT work, even if a 9 volt battery is installed.19 20
T/P RINGER
ON/OFF
DC10V650mA
USEONLYWITHCLASS2POWERSOURCE
-+
WhenThe "VOL/RING" button ispressed,the receiver volume willincreaseto maximum (level 3) and thenbackdown and decrease to minimum(level1) in a repeated cycle.Pressthe "PAGE" button on the base once,andthe handset will beep 3 times. Press andholdthe "PAGE" button for 3 seconds, andthehandset will beep for about 60 seconds.Pressany button on the handset to stop thehandsetfrom beeping.
FUNCTION
R
A
D
I
O
O
N
/
O
F
F
E
N
T
E
R
FUNCTION
R
A
D
I
O
O
N
/
O
F
F
E
N
T
E
R
BACKLIGHT
BRIGHT/NORMAL/OFF