Appendix B Dip Switch Setting | Star Micronics TSP1000 manual

Appendix B: Dip Switch Setting

Appendix B: Dip Switch Setting

Two DIP switches are provided at the bottom of the printer, and can be set as given in the table below. Be sure to set the power switch to off before changing the settings. It is recommended to use a pointed item like a pen or flat-blade driver screw to change the settings. The settings will become effective when the power switch is set to on again.

The following is the procedure for changing the settings on DIP switches.

1.Make sure the printer is turned off.

2.Remove the screw from the DIP switch cover. Then take off the DIP switch cover, as shown in the illustration below.

3.Set the switches using a pointed tool, such as a pen or flat-blade screwdriver.

4.Replace the DIP switch cover. Then secure it with the screw. The new settings take effect when you turn on the printer.

– 31 –

Image 35

Star Micronics TSP1000 user manual Appendix B Dip Switch Setting

Contents

USER’S MANUAL TSP1000 SERIESTHERMAL PRINTER Page Radio Interference Regulations Federal Communications Commission Radio Frequency InterferenceStatement Statement of The Canadian Department of Communications TABLE OF CONTENTS 1-1. Unpacking 1. Unpacking and Installation 2. Parts Identification and Nomenclature Choosing a place for the printer Core inner 3. Consumable Parts and AC AdapterCore outer Page 4-1-1. Serial Interface RS-232C Cable 4. Connecting Cables and AC Adapter4-1. Interface Cable 5 cm maximum Fastener Pull and cut 4-1-2. Parallel Interface CableFerrite core Interface cable Parallel interface cable 4-1-3. Connecting USB Cable 10cm 4-1-4. Connecting Ethernet CableEthernet cable Ferrite core 4-2. Connecting to a Buzzer Drive 4-3. Connecting the Optional AC Adapter Make sure that the AC adapter has been connected as described in 4-4. Turning Power On Install the cable as shown in the diagram below 4-5. Installing the Cable 4-6. Switch Blind Installation 5-1. Control Panel Errors5. Control Panel and Other Functions 4 Paper detection error 3 Non recoverable error1 If a non recoverable error occurs, turn the power OFF immediately 5-3. Self Printing 1 Push the Cover open lever, and open the printer cover 6. Loading the Roll PaperBe sure to use roll paper that matches the printer’s specification Note Make sure that the printer cover is securely closed 1. Do not touch the cutter blade 7. Adjusting the Near-end Sensor Adjustment value according to the paper you are using 8-2. Removing Paper Jam 8. Preventing and Clearing Paper Jams8-1. Preventing Paper Jams 8-3. Releasing a Locked Cutter 1 Do not apply extreme pressure to the moving blade 6 Install the front cover, and then set the power switch to ON 9-2. Cleaning the Paper Holder 9. Periodical Cleaning9-1. Cleaning the Thermal Head A-1. General Specifications Appendix A Specifications A-5. Option A-2. Auto Cutter SpecificationsA-4. Electrical Characteristics A-3. Interface 1.0 million cuttings if the paper thickness is 100 µm A-6. Environmental RequirementsA-7. Reliability 20 million lines based on an average printing rate of Remarks A-8. Black Mark Specifications Appendix B Dip Switch Setting No. 1 2 3 DIP-SW2 B-1. Parallel Interface ModelNo. 1 2 3 4 5 6 7 DIP-SW1 B-2. Sperial Interface RS-232C Model DIP-SW3 DIP switch Printer Driver URL B-3. USB Interface Model B-4. Ethernet Interface Model LED Display Installing the Printer Driver and the LPR Port Driver SetGreen Lights when other party connection is recognized as 10BASE-T Orange Lights when packets are received Appendix C Parallel Interface Table of Connection Signals for Each Mode Appendix D Serial Interface RS-232C D-1. RS-232C Connector DIP SW D-sub 25 PinD-sub 9 Pin Printer status D-sub 25 pin D-3. Electrical CharacteristicsD-2. Cable Connections Host side Appendix E USB Interface and Ethernet Interface E-1. USB Interface SpecificationsE-2. Ethernet Interface Specifications Modular plug Appendix F Buzzer Driver Circuit Drive circuit Appendix G Memory Switch Settings Page Page OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC