B-4. Ethernet Interface Model, DIP-SW1 | Star Micronics TSP1000

B-4. Ethernet Interface Model

ON

OFF

No. 1 2 3 4 5 6 7 8

DIP-SW1

ON

OFF

No. 1 2 3 4

DIP-SW2

DIP-SW1

Switch				Function			ON	OFF

1-1		Command emulation					See table below

1-2		Command emulation
1-2		Command emulation
1-3	Should not be changed (Should be set to on)

1-4		Sensor adjustment					Valid	Invalid

1-5	Should not be changed (Should be set to on)
1-6		Handshaking coditions					Offline or receive	Receive buffer full
		(conditions for BUSY)					buffer full

1-7	Should not be changed (Should be set to on)
1-8	Should not be changed (Should be set to on)
The factory settings of DIP switch are all on.

Switch 1-1				Switch 1-2			Command emulation

		ON		ON			Star Line Mode

		OFF		ON			Star Page Mode

		OFF		OFF			ESC/POS Mode

				DIP-SW 2

Switch				Function			ON	OFF

2-1~2-4				Always ON			Should be set to on

The factory settings of DIP switch are all on.

– 36 –

Image 40

Star Micronics TSP1000 B-4. Ethernet Interface Model, DIP-SW1, The factory settings of DIP switch are all on, Dip-Sw

Contents

THERMAL PRINTER TSP1000 SERIESUSER’S MANUAL Page Federal Communications Commission Radio Frequency Interference StatementStatement of The Canadian Department of Communications Radio Interference Regulations TABLE OF CONTENTS 1. Unpacking and Installation 1-1. Unpacking 2. Parts Identification and Nomenclature Choosing a place for the printer Core outer 3. Consumable Parts and AC AdapterCore inner Page 4-1. Interface Cable 4. Connecting Cables and AC Adapter4-1-1. Serial Interface RS-232C Cable Ferrite core Interface cable 4-1-2. Parallel Interface Cable5 cm maximum Fastener Pull and cut 4-1-3. Connecting USB Cable Parallel interface cable 4-1-4. Connecting Ethernet Cable Ethernet cableFerrite core 10cm 4-2. Connecting to a Buzzer Drive 4-3. Connecting the Optional AC Adapter 4-4. Turning Power On Make sure that the AC adapter has been connected as described in 4-5. Installing the Cable Install the cable as shown in the diagram below 4-6. Switch Blind Installation 5. Control Panel and Other Functions Errors5-1. Control Panel 1 If a non recoverable error occurs, turn the power OFF immediately 3 Non recoverable error4 Paper detection error 5-3. Self Printing Be sure to use roll paper that matches the printer’s specification 6. Loading the Roll Paper1 Push the Cover open lever, and open the printer cover Note Make sure that the printer cover is securely closed 1. Do not touch the cutter blade 7. Adjusting the Near-end Sensor Adjustment value according to the paper you are using 8-1. Preventing Paper Jams 8. Preventing and Clearing Paper Jams8-2. Removing Paper Jam 8-3. Releasing a Locked Cutter 6 Install the front cover, and then set the power switch to ON 1 Do not apply extreme pressure to the moving blade 9-1. Cleaning the Thermal Head 9. Periodical Cleaning9-2. Cleaning the Paper Holder Appendix A Specifications A-1. General Specifications A-2. Auto Cutter Specifications A-4. Electrical CharacteristicsA-3. Interface A-5. Option A-6. Environmental Requirements A-7. Reliability20 million lines based on an average printing rate of 1.0 million cuttings if the paper thickness is 100 µm A-8. Black Mark Specifications Remarks Appendix B Dip Switch Setting No. 1 2 3 4 5 6 7 DIP-SW1 B-1. Parallel Interface ModelNo. 1 2 3 DIP-SW2 B-2. Sperial Interface RS-232C Model DIP switch DIP-SW3 B-3. USB Interface Model Printer Driver URL B-4. Ethernet Interface Model Installing the Printer Driver and the LPR Port Driver Set Green Lights when other party connection is recognized as 10BASE-TOrange Lights when packets are received LED Display Table of Connection Signals for Each Mode Appendix C Parallel Interface D-1. RS-232C Connector Appendix D Serial Interface RS-232C D-sub 25 Pin D-sub 9 PinPrinter status DIP SW D-3. Electrical Characteristics D-2. Cable ConnectionsHost side D-sub 25 pin E-2. Ethernet Interface Specifications E-1. USB Interface SpecificationsAppendix E USB Interface and Ethernet Interface Appendix F Buzzer Driver Circuit Modular plug Drive circuit Appendix G Memory Switch Settings Page Page OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC