Manuals / Star Micronics / Computer Equipment / Printer

Star Micronics TSP1000 user manual

Models: TSP1000

1 52

Download 52 pages 58.91 Kb

Page 51

Image 51

Star Micronics TSP1000 user manual

Contents

TSP1000 SERIES THERMAL PRINTERUSER’S MANUAL Page Radio Interference Regulations Federal Communications Commission Radio Frequency InterferenceStatement Statement of The Canadian Department of CommunicationsTABLE OF CONTENTS 1-1. Unpacking 1. Unpacking and Installation2. Parts Identification and Nomenclature Choosing a place for the printer 3. Consumable Parts and AC Adapter Core outerCore inner Page 4. Connecting Cables and AC Adapter 4-1. Interface Cable4-1-1. Serial Interface RS-232C Cable 4-1-2. Parallel Interface Cable Ferrite core Interface cable5 cm maximum Fastener Pull and cut Parallel interface cable 4-1-3. Connecting USB Cable10cm 4-1-4. Connecting Ethernet CableEthernet cable Ferrite core4-2. Connecting to a Buzzer Drive 4-3. Connecting the Optional AC Adapter Make sure that the AC adapter has been connected as described in 4-4. Turning Power OnInstall the cable as shown in the diagram below 4-5. Installing the Cable4-6. Switch Blind Installation Errors 5. Control Panel and Other Functions5-1. Control Panel 3 Non recoverable error 1 If a non recoverable error occurs, turn the power OFF immediately4 Paper detection error 5-3. Self Printing 6. Loading the Roll Paper Be sure to use roll paper that matches the printer’s specification1 Push the Cover open lever, and open the printer cover Note Make sure that the printer cover is securely closed 1. Do not touch the cutter blade 7. Adjusting the Near-end Sensor Adjustment value according to the paper you are using 8. Preventing and Clearing Paper Jams 8-1. Preventing Paper Jams8-2. Removing Paper Jam 8-3. Releasing a Locked Cutter 1 Do not apply extreme pressure to the moving blade 6 Install the front cover, and then set the power switch to ON9. Periodical Cleaning 9-1. Cleaning the Thermal Head9-2. Cleaning the Paper Holder A-1. General Specifications Appendix A SpecificationsA-5. Option A-2. Auto Cutter SpecificationsA-4. Electrical Characteristics A-3. Interface1.0 million cuttings if the paper thickness is 100 µm A-6. Environmental RequirementsA-7. Reliability 20 million lines based on an average printing rate ofRemarks A-8. Black Mark SpecificationsAppendix B Dip Switch Setting B-1. Parallel Interface Model No. 1 2 3 4 5 6 7 DIP-SW1No. 1 2 3 DIP-SW2 DIP-SW B-2. Sperial Interface RS-232C ModelThe factory settings of DIP switch are all on The factory settings of DIP switch are all onDIP-SW3 DIP switchPrinter Driver URL B-3. USB Interface ModelDIP-SW1 B-4. Ethernet Interface ModelThe factory settings of DIP switch are all on The factory settings of DIP switch are all onLED Display Installing the Printer Driver and the LPR Port Driver SetGreen Lights when other party connection is recognized as 10BASE-T Orange Lights when packets are receivedAppendix C Parallel Interface Table of Connection Signals for Each ModeAppendix D Serial Interface RS-232C D-1. RS-232C ConnectorDirection D-sub 25 PinD-sub 9 Pin Pin NoD-sub 25 pin D-3. Electrical CharacteristicsD-2. Cable Connections Host sideE-1. USB Interface Specifications E-2. Ethernet Interface SpecificationsAppendix E USB Interface and Ethernet Interface Modular plug Appendix F Buzzer Driver CircuitDrive circuit Appendix G Memory Switch Settings Page Page OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC