Star Micronics TSP1000 guide

1)Do not apply extreme pressure to the moving blade.

(4)If the cutter’s moving blade is protruding, rotate the knob in the direction of an arrow to return the moving blade to its home position.

When the check window is completely white, the moving blade is at its home position.

Note:

1)Do not apply extreme pressure to the moving blade.

2)If the moving blade is protruding too much, the printer cover cannot be opened. Trying to open the printer cover may damage the cutter.

(5)Open the printer cover, remove any jammed paper, and then re-install the paper roll.

(6)Install the front cover, and then set the power switch to ON.

– 25 –

Image 29

Star Micronics TSP1000 user manual Do not apply extreme pressure to the moving blade

Contents

USER’S MANUAL TSP1000 SERIESTHERMAL PRINTER Page Statement Federal Communications Commission Radio Frequency InterferenceStatement of The Canadian Department of Communications Radio Interference Regulations TABLE OF CONTENTS 1-1. Unpacking 1. Unpacking and Installation 2. Parts Identification and Nomenclature Choosing a place for the printer Core inner 3. Consumable Parts and AC AdapterCore outer Page 4-1-1. Serial Interface RS-232C Cable 4. Connecting Cables and AC Adapter4-1. Interface Cable 5 cm maximum Fastener Pull and cut 4-1-2. Parallel Interface CableFerrite core Interface cable Parallel interface cable 4-1-3. Connecting USB Cable Ethernet cable 4-1-4. Connecting Ethernet CableFerrite core 10cm 4-2. Connecting to a Buzzer Drive 4-3. Connecting the Optional AC Adapter Make sure that the AC adapter has been connected as described in 4-4. Turning Power On Install the cable as shown in the diagram below 4-5. Installing the Cable 4-6. Switch Blind Installation 5-1. Control Panel Errors5. Control Panel and Other Functions 4 Paper detection error 3 Non recoverable error1 If a non recoverable error occurs, turn the power OFF immediately 5-3. Self Printing 1 Push the Cover open lever, and open the printer cover 6. Loading the Roll PaperBe sure to use roll paper that matches the printer’s specification Note Make sure that the printer cover is securely closed 1. Do not touch the cutter blade 7. Adjusting the Near-end Sensor Adjustment value according to the paper you are using 8-2. Removing Paper Jam 8. Preventing and Clearing Paper Jams8-1. Preventing Paper Jams 8-3. Releasing a Locked Cutter 1 Do not apply extreme pressure to the moving blade 6 Install the front cover, and then set the power switch to ON 9-2. Cleaning the Paper Holder 9. Periodical Cleaning9-1. Cleaning the Thermal Head A-1. General Specifications Appendix A Specifications A-4. Electrical Characteristics A-2. Auto Cutter SpecificationsA-3. Interface A-5. Option A-7. Reliability A-6. Environmental Requirements20 million lines based on an average printing rate of 1.0 million cuttings if the paper thickness is 100 µm Remarks A-8. Black Mark Specifications Appendix B Dip Switch Setting No. 1 2 3 DIP-SW2 B-1. Parallel Interface ModelNo. 1 2 3 4 5 6 7 DIP-SW1 B-2. Sperial Interface RS-232C Model DIP-SW3 DIP switch Printer Driver URL B-3. USB Interface Model B-4. Ethernet Interface Model Green Lights when other party connection is recognized as 10BASE-T Installing the Printer Driver and the LPR Port Driver SetOrange Lights when packets are received LED Display Appendix C Parallel Interface Table of Connection Signals for Each Mode Appendix D Serial Interface RS-232C D-1. RS-232C Connector D-sub 9 Pin D-sub 25 PinPrinter status DIP SW D-2. Cable Connections D-3. Electrical CharacteristicsHost side D-sub 25 pin Appendix E USB Interface and Ethernet Interface E-1. USB Interface SpecificationsE-2. Ethernet Interface Specifications Modular plug Appendix F Buzzer Driver Circuit Drive circuit Appendix G Memory Switch Settings Page Page OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC