Manuals / Star Micronics / Computer Equipment / Printer

Star Micronics TSP1000 user manual Parallel Interface Cable, Ferrite core Interface cable

Models: TSP1000

1 52

Download 52 pages 58.91 Kb

Page 11

4-1-2. Parallel Interface Cable

4-1-2. Parallel Interface Cable

(1) Make sure the printer is turn off.

(2) For only the parallel interface model, affix the ferrite core onto the cable as shown in the illustration below.

Ferrite core

Interface cable

5cm maximum

Fastener

Pull and cut

(3)Pass the fastener through the ferrite core.

(4)Loop the fastener around the cable and lock it. Use scissors to cut off any excess.

– 7 –

Image 11

Star Micronics TSP1000 user manual Parallel Interface Cable, Ferrite core Interface cable, cm maximum Fastener Pull and cut

Contents

USER’S MANUAL TSP1000 SERIESTHERMAL PRINTER Page Radio Interference Regulations Federal Communications Commission Radio Frequency InterferenceStatement Statement of The Canadian Department of CommunicationsTABLE OF CONTENTS 1-1. Unpacking 1. Unpacking and Installation2. Parts Identification and Nomenclature Choosing a place for the printer Core inner 3. Consumable Parts and AC AdapterCore outer Page 4-1-1. Serial Interface RS-232C Cable 4. Connecting Cables and AC Adapter4-1. Interface Cable 5 cm maximum Fastener Pull and cut 4-1-2. Parallel Interface CableFerrite core Interface cable Parallel interface cable 4-1-3. Connecting USB Cable10cm 4-1-4. Connecting Ethernet CableEthernet cable Ferrite core4-2. Connecting to a Buzzer Drive 4-3. Connecting the Optional AC Adapter Make sure that the AC adapter has been connected as described in 4-4. Turning Power OnInstall the cable as shown in the diagram below 4-5. Installing the Cable4-6. Switch Blind Installation 5-1. Control Panel Errors5. Control Panel and Other Functions 4 Paper detection error 3 Non recoverable error1 If a non recoverable error occurs, turn the power OFF immediately 5-3. Self Printing 1 Push the Cover open lever, and open the printer cover 6. Loading the Roll PaperBe sure to use roll paper that matches the printer’s specification Note Make sure that the printer cover is securely closed 1. Do not touch the cutter blade 7. Adjusting the Near-end Sensor Adjustment value according to the paper you are using 8-2. Removing Paper Jam 8. Preventing and Clearing Paper Jams8-1. Preventing Paper Jams 8-3. Releasing a Locked Cutter 1 Do not apply extreme pressure to the moving blade 6 Install the front cover, and then set the power switch to ON9-2. Cleaning the Paper Holder 9. Periodical Cleaning9-1. Cleaning the Thermal Head A-1. General Specifications Appendix A SpecificationsA-5. Option A-2. Auto Cutter SpecificationsA-4. Electrical Characteristics A-3. Interface1.0 million cuttings if the paper thickness is 100 µm A-6. Environmental RequirementsA-7. Reliability 20 million lines based on an average printing rate ofRemarks A-8. Black Mark SpecificationsAppendix B Dip Switch Setting No. 1 2 3 DIP-SW2 B-1. Parallel Interface ModelNo. 1 2 3 4 5 6 7 DIP-SW1 DIP-SW B-2. Sperial Interface RS-232C ModelThe factory settings of DIP switch are all on The factory settings of DIP switch are all onDIP-SW3 DIP switchPrinter Driver URL B-3. USB Interface ModelDIP-SW1 B-4. Ethernet Interface ModelThe factory settings of DIP switch are all on The factory settings of DIP switch are all onLED Display Installing the Printer Driver and the LPR Port Driver SetGreen Lights when other party connection is recognized as 10BASE-T Orange Lights when packets are receivedAppendix C Parallel Interface Table of Connection Signals for Each ModeAppendix D Serial Interface RS-232C D-1. RS-232C ConnectorDirection D-sub 25 PinD-sub 9 Pin Pin NoD-sub 25 pin D-3. Electrical CharacteristicsD-2. Cable Connections Host sideAppendix E USB Interface and Ethernet Interface E-1. USB Interface SpecificationsE-2. Ethernet Interface Specifications Modular plug Appendix F Buzzer Driver CircuitDrive circuit Appendix G Memory Switch Settings Page Page OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC