Parts Identification and Nomenclature | Star Micronics TSP1000

2. Parts Identification and Nomenclature

2. Parts Identification and Nomenclature

Printer cover

Open this cover to load or replace paper.

Power switch

Used to turn on/off power to the printer.

Cover open lever

Push this lever in the direction of the arrow to open the printer cover.

Control panel

Features LED indica- tors to indicate printer status and switches to operate the printer.

Interface connector

For connection to a host computer.

Buzzer drive connector

Connects to buzzer. Do not connect this to a telephone.

Power connector

For connection of the AC adapter. Never unplug the AC adapter while the printer is on.

– 2 –

Image 6

Star Micronics TSP1000 user manual Parts Identification and Nomenclature

Contents

TSP1000 SERIES THERMAL PRINTERUSER’S MANUAL Page Statement of The Canadian Department of Communications Federal Communications Commission Radio Frequency InterferenceStatement Radio Interference Regulations TABLE OF CONTENTS 1. Unpacking and Installation 1-1. Unpacking 2. Parts Identification and Nomenclature Choosing a place for the printer 3. Consumable Parts and AC Adapter Core outerCore inner Page 4. Connecting Cables and AC Adapter 4-1. Interface Cable4-1-1. Serial Interface RS-232C Cable 4-1-2. Parallel Interface Cable Ferrite core Interface cable5 cm maximum Fastener Pull and cut 4-1-3. Connecting USB Cable Parallel interface cable Ferrite core 4-1-4. Connecting Ethernet CableEthernet cable 10cm 4-2. Connecting to a Buzzer Drive 4-3. Connecting the Optional AC Adapter 4-4. Turning Power On Make sure that the AC adapter has been connected as described in 4-5. Installing the Cable Install the cable as shown in the diagram below 4-6. Switch Blind Installation Errors 5. Control Panel and Other Functions5-1. Control Panel 3 Non recoverable error 1 If a non recoverable error occurs, turn the power OFF immediately4 Paper detection error 5-3. Self Printing 6. Loading the Roll Paper Be sure to use roll paper that matches the printer’s specification1 Push the Cover open lever, and open the printer cover Note Make sure that the printer cover is securely closed 1. Do not touch the cutter blade 7. Adjusting the Near-end Sensor Adjustment value according to the paper you are using 8. Preventing and Clearing Paper Jams 8-1. Preventing Paper Jams8-2. Removing Paper Jam 8-3. Releasing a Locked Cutter 6 Install the front cover, and then set the power switch to ON 1 Do not apply extreme pressure to the moving blade 9. Periodical Cleaning 9-1. Cleaning the Thermal Head9-2. Cleaning the Paper Holder Appendix A Specifications A-1. General Specifications A-3. Interface A-2. Auto Cutter SpecificationsA-4. Electrical Characteristics A-5. Option 20 million lines based on an average printing rate of A-6. Environmental RequirementsA-7. Reliability 1.0 million cuttings if the paper thickness is 100 µm A-8. Black Mark Specifications Remarks Appendix B Dip Switch Setting B-1. Parallel Interface Model No. 1 2 3 4 5 6 7 DIP-SW1No. 1 2 3 DIP-SW2 B-2. Sperial Interface RS-232C Model DIP switch DIP-SW3 B-3. USB Interface Model Printer Driver URL B-4. Ethernet Interface Model Orange Lights when packets are received Installing the Printer Driver and the LPR Port Driver SetGreen Lights when other party connection is recognized as 10BASE-T LED Display Table of Connection Signals for Each Mode Appendix C Parallel Interface D-1. RS-232C Connector Appendix D Serial Interface RS-232C Printer status D-sub 25 PinD-sub 9 Pin DIP SW Host side D-3. Electrical CharacteristicsD-2. Cable Connections D-sub 25 pin E-1. USB Interface Specifications E-2. Ethernet Interface SpecificationsAppendix E USB Interface and Ethernet Interface Appendix F Buzzer Driver Circuit Modular plug Drive circuit Appendix G Memory Switch Settings Page Page OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC