DIP switch, DIP-SW3 | Star Micronics TSP1000 specs

DIP switch 3

The following is the procedure for changing the settings on DIP switch No. 3.

1.Turn off the printer and all components connected to it.

2.Remove the 2 screws.

3.Remove the serial interface board unit.

4.Change the setting of the DIP switches.

5.Replace the serial interface board unit. Then secure it with the screws.

6.Turn on the printer and all components connected to it.

		ON
	DIP switch 3	OFF
	DIP switch 3	No.	1	2	3	4	5	6	7	8
		No.	1	2	3	4	5	6	7	8

DIP-SW3

The factory settings of DIP switch are all on, except for switches 7 and 8.

DIP-SW 3

Switch			Function			ON		OFF

3-1			Baud Rate				See table below

3-2
3-2

3-3			Data Length			8 bits		7 bits

3-4			Parity Check			Disabled		Enabled

3-5			Parity			Odd		Even

3-6			Handshake			DTR/DSR		XON/XOFF

3-7		Should not be changed (Should be set to off)				—		—

3-8
3-8


		Baud Rate		Switch 3-1				Switch 3-2

		4800BPS		OFF				ON

		9600BPS		ON				ON

		19200BPS		ON				OFF

		38400BPS		OFF				OFF

– 34 –

Image 38

Star Micronics TSP1000 user manual DIP switch, DIP-SW3

Contents

USER’S MANUAL TSP1000 SERIESTHERMAL PRINTER Page Statement of The Canadian Department of Communications Federal Communications Commission Radio Frequency InterferenceStatement Radio Interference Regulations TABLE OF CONTENTS 1. Unpacking and Installation 1-1. Unpacking 2. Parts Identification and Nomenclature Choosing a place for the printer Core inner 3. Consumable Parts and AC AdapterCore outer Page 4-1-1. Serial Interface RS-232C Cable 4. Connecting Cables and AC Adapter4-1. Interface Cable 5 cm maximum Fastener Pull and cut 4-1-2. Parallel Interface CableFerrite core Interface cable 4-1-3. Connecting USB Cable Parallel interface cable Ferrite core 4-1-4. Connecting Ethernet CableEthernet cable 10cm 4-2. Connecting to a Buzzer Drive 4-3. Connecting the Optional AC Adapter 4-4. Turning Power On Make sure that the AC adapter has been connected as described in 4-5. Installing the Cable Install the cable as shown in the diagram below 4-6. Switch Blind Installation 5-1. Control Panel Errors5. Control Panel and Other Functions 4 Paper detection error 3 Non recoverable error1 If a non recoverable error occurs, turn the power OFF immediately 5-3. Self Printing 1 Push the Cover open lever, and open the printer cover 6. Loading the Roll PaperBe sure to use roll paper that matches the printer’s specification Note Make sure that the printer cover is securely closed 1. Do not touch the cutter blade 7. Adjusting the Near-end Sensor Adjustment value according to the paper you are using 8-2. Removing Paper Jam 8. Preventing and Clearing Paper Jams8-1. Preventing Paper Jams 8-3. Releasing a Locked Cutter 6 Install the front cover, and then set the power switch to ON 1 Do not apply extreme pressure to the moving blade 9-2. Cleaning the Paper Holder 9. Periodical Cleaning9-1. Cleaning the Thermal Head Appendix A Specifications A-1. General Specifications A-3. Interface A-2. Auto Cutter SpecificationsA-4. Electrical Characteristics A-5. Option 20 million lines based on an average printing rate of A-6. Environmental RequirementsA-7. Reliability 1.0 million cuttings if the paper thickness is 100 µm A-8. Black Mark Specifications Remarks Appendix B Dip Switch Setting No. 1 2 3 DIP-SW2 B-1. Parallel Interface ModelNo. 1 2 3 4 5 6 7 DIP-SW1 B-2. Sperial Interface RS-232C Model DIP switch DIP-SW3 B-3. USB Interface Model Printer Driver URL B-4. Ethernet Interface Model Orange Lights when packets are received Installing the Printer Driver and the LPR Port Driver SetGreen Lights when other party connection is recognized as 10BASE-T LED Display Table of Connection Signals for Each Mode Appendix C Parallel Interface D-1. RS-232C Connector Appendix D Serial Interface RS-232C Printer status D-sub 25 PinD-sub 9 Pin DIP SW Host side D-3. Electrical CharacteristicsD-2. Cable Connections D-sub 25 pin Appendix E USB Interface and Ethernet Interface E-1. USB Interface SpecificationsE-2. Ethernet Interface Specifications Appendix F Buzzer Driver Circuit Modular plug Drive circuit Appendix G Memory Switch Settings Page Page OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC