B-2. Sperial Interface RS-232C Model | Star Micronics TSP1000

B-2. Sperial Interface (RS-232C) Model

ON

OFF

No. 1 2 3 4 5 6 7 8

DIP-SW1

ON

OFF

No. 1 2 3 4

DIP-SW2

DIP-SW 1

Switch	Function		ON	OFF

1-1	Command emulation		See table below

1-2	Command emulation
1-2	Command emulation

1-3	Should not be changed (Should be set to on)

1-4	Sensor adjustment		Valid	Invalid

1-5	Should not be changed (Should be set to on)

1-6	Handshaking conditions		Offline or receive	Receive buffer full
	(conditions for BUSY)		buffer full

1-7	Automatic status back function		Invalid	Valid

1-8	Should not be changed (Should be set to on)

The factory settings of DIP switch are all on.

Switch 1-1	Switch 1-2	Command emulation

ON	ON	Star Line Mode

OFF	ON	Star Page Mode

OFF	OFF	ESC/POS Mode

DIP-SW 2

Switch	Function	ON		OFF

2-1

2-2	Always ON		Should be set to on

2-3
2-3

2-4

The factory settings of DIP switch are all on.

– 33 –

Image 37

Star Micronics TSP1000 B-2. Sperial Interface RS-232C Model, Dip-Sw, The factory settings of DIP switch are all on

Contents

THERMAL PRINTER TSP1000 SERIESUSER’S MANUAL Page Statement Federal Communications Commission Radio Frequency InterferenceStatement of The Canadian Department of Communications Radio Interference Regulations TABLE OF CONTENTS 1-1. Unpacking 1. Unpacking and Installation 2. Parts Identification and Nomenclature Choosing a place for the printer Core outer 3. Consumable Parts and AC AdapterCore inner Page 4-1. Interface Cable 4. Connecting Cables and AC Adapter4-1-1. Serial Interface RS-232C Cable Ferrite core Interface cable 4-1-2. Parallel Interface Cable5 cm maximum Fastener Pull and cut Parallel interface cable 4-1-3. Connecting USB Cable Ethernet cable 4-1-4. Connecting Ethernet CableFerrite core 10cm 4-2. Connecting to a Buzzer Drive 4-3. Connecting the Optional AC Adapter Make sure that the AC adapter has been connected as described in 4-4. Turning Power On Install the cable as shown in the diagram below 4-5. Installing the Cable 4-6. Switch Blind Installation 5. Control Panel and Other Functions Errors5-1. Control Panel 1 If a non recoverable error occurs, turn the power OFF immediately 3 Non recoverable error4 Paper detection error 5-3. Self Printing Be sure to use roll paper that matches the printer’s specification 6. Loading the Roll Paper1 Push the Cover open lever, and open the printer cover Note Make sure that the printer cover is securely closed 1. Do not touch the cutter blade 7. Adjusting the Near-end Sensor Adjustment value according to the paper you are using 8-1. Preventing Paper Jams 8. Preventing and Clearing Paper Jams8-2. Removing Paper Jam 8-3. Releasing a Locked Cutter 1 Do not apply extreme pressure to the moving blade 6 Install the front cover, and then set the power switch to ON 9-1. Cleaning the Thermal Head 9. Periodical Cleaning9-2. Cleaning the Paper Holder A-1. General Specifications Appendix A Specifications A-4. Electrical Characteristics A-2. Auto Cutter SpecificationsA-3. Interface A-5. Option A-7. Reliability A-6. Environmental Requirements20 million lines based on an average printing rate of 1.0 million cuttings if the paper thickness is 100 µm Remarks A-8. Black Mark Specifications Appendix B Dip Switch Setting No. 1 2 3 4 5 6 7 DIP-SW1 B-1. Parallel Interface ModelNo. 1 2 3 DIP-SW2 B-2. Sperial Interface RS-232C Model DIP-SW3 DIP switch Printer Driver URL B-3. USB Interface Model B-4. Ethernet Interface Model Green Lights when other party connection is recognized as 10BASE-T Installing the Printer Driver and the LPR Port Driver SetOrange Lights when packets are received LED Display Appendix C Parallel Interface Table of Connection Signals for Each Mode Appendix D Serial Interface RS-232C D-1. RS-232C Connector D-sub 9 Pin D-sub 25 PinPrinter status DIP SW D-2. Cable Connections D-3. Electrical CharacteristicsHost side D-sub 25 pin E-2. Ethernet Interface Specifications E-1. USB Interface SpecificationsAppendix E USB Interface and Ethernet Interface Modular plug Appendix F Buzzer Driver Circuit Drive circuit Appendix G Memory Switch Settings Page Page OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC