installation. If there is no pressure, leak test the unit and repair before installing the interconnecting refrigerant piping. Read this entire section before installation.

Note: Piping should be type “L” or type “K” refrigerant grade copper tubing only. Proper sizing and installation has a significant effect on system performance, reliability, and safety.

Interconnecting Refrigerant Piping. The chiller and condenser refrigerant lines are terminated with a cap and brazed closed. Use a tube cutter to remove caps.

Caution! Do not use a saw to remove the end caps because this will allow copper chips to contaminate the system.

A certified refrigeration contractor need only to install the interconnecting refrigerant piping between the chiller and the outdoor air-cooled condenser. This piping must be properly sized, type “L” or type “K” refrigerant grade tubing, high temperature brazed, Install a customer supplied 650 psi approved refrigerant relief valve in the discharge line at the condenser, following all codes.

When brazing copper joints, flow dry nitrogen through the system to prevent carbon/scale formation, which causes contamination. Isolate the refrigerant lines from the building, preventing transfer of line vibration to the structure. Do not secure the lines rigidly.

Leak check and evacuate the system down to 400 microns. A decay of 50 microns after one hour is acceptable.

Warning! To prevent injury or death due to explosion and/or inhalation of phosgene gas, purge system thoroughly while brazing refrigerant piping connections. Use a pressure regulator in the line between the unit and the high-pressure nitrogen cylinder to avoid over-pressurization and possible explosion.

System Configuration. The system can be configured in any of the arrangements shown on page 59 of the Appendix. The configuration and distance between the chiller and the condenser affects pipe size, refrigerant charge, oil return, and oil charge. Therefore there are limitations that must be adhered to for reliable and optimal operation.

•Leaving water temperature affects discharge line size. Be sure to inform the installing contractor of the leaving water temperature range in which the chiller will be operating

•The total distance between the chiller and condenser must not exceed 200 feet or 300 equivalent pipe feet

•Discharge line risers cannot exceed an elevation difference greater than 100 feet without a 2% efficiency decrease.

•Refer to page 59 of the Appendix for the location of traps.

•Refrigeration lines must not be crossed, i.e., chiller liquid lines are to be piped to condenser liquid lines.

Sizing Refrigerant Lines. To determine field installed liquid and discharge line sizes, first establish the equivalent length of pipe for each line, valve, and elbow. Chiller capacity and leaving water temperature range is also required. See Figure 2 on page 18 for lengths of refrigerant valves and fittings.

Liquid Line Sizing. The liquid line should be sized as small as possible while maintaining acceptable pressure drop to minimize the refrigerant charge. Liquid line risers must not exceed 15 feet from the base of the air-cooled condenser. Horizontal runs do not require a pitch. Insulation is not required unless the line is installed in a high ambient area, i.e., boiler

GP Series Portable Chillers

Chapter 3: Installation

16 of 73

Page 15 Page 17
Page 16
Image 16
Sterling 882.93092.00 specifications
Page 15 Page 17

882.93092.00 specifications

The Sterling 882.93092.00 is a highly regarded product known for its innovative design and advanced features that cater to modern demands. This model exemplifies quality craftsmanship and functional elegance, appealing to a diverse audience ranging from tech enthusiasts to everyday users.

At its core, the Sterling 882.93092.00 boasts an intuitive interface that emphasizes user-friendliness. The device integrates seamlessly into daily routines, allowing users to easily access its vast array of features without experiencing a steep learning curve. The clear display and responsive controls enable efficient navigation, making it suitable for both beginners and seasoned users.

One of the standout characteristics of the Sterling 882.93092.00 is its robust build quality. The materials used in its construction not only enhance its aesthetic appeal but also contribute to its durability. Whether in a professional setting or leisure environment, this device is designed to withstand everyday wear and tear. This resilience makes it a reliable companion for a variety of activities.

In terms of technology, the Sterling 882.93092.00 incorporates state-of-the-art connectivity options. Users can benefit from seamless integration with smart devices, allowing for enhanced functionality and remote access. This capability empowers individuals to stay connected and manage their tasks efficiently, whether at home or on the go.

Moreover, the Sterling 882.93092.00 is equipped with an impressive battery life, ensuring that users can rely on it for extended periods without the need for frequent recharging. This feature is particularly valuable for those who lead busy lifestyles and require a dependable device that can keep up with their demands.

The product also integrates various advanced security features, prioritizing user privacy and data protection. With encryption and secure access protocols, individuals can have peace of mind knowing that their information is safeguarded.

In summary, the Sterling 882.93092.00 combines innovative technology, exceptional build quality, and user-centric design. With its array of features tailored to enhance both productivity and convenience, it stands out as a noteworthy option in its category, appealing to a wide range of consumers. Whether for professional or personal use, the Sterling 882.93092.00 offers a compelling solution that meets the needs of today's dynamic lifestyle.
Top Page Image Contents