Sterling SSE-5 BL - page 51

SSE 5 BL

Spare parts list 37

10.2. Accessories

F Please observe the operating manuals in chapter 11.

Contents

Main Page Page Asia/Australia +86 512 8717 1919 Sales and Contracting Department Table of contents Page Page 1.1. Warnings and symbols This symbol indicates danger to life! Fatal or serious injury is L This symbol indicates that serious injury is possible if the F This symbol indicates that extensive damage to equipment is & This symbol indicates information important for becoming $ This symbol indicates that a technical term is explained at this 1.2. Explanations and information 1.3. Legal basis 1.4. Fields of applications 1.5. Notes on usage 2. Safety instructions These safety instructions apply to all persons within the range of Safety instructions 2-2 2.1. For your safety 2.1.1. General Safety instructions 2-3 2.1.2. Assembly Safety instructions 2-4 2.1.3. Operation 2.1.4. Maintenance Safety instructions 2-5 2.2. For the operating safety of the equipment 3. Putting into operation This chapter is intended for operating personnel. F Make sure the plastic stopper has been removed from the 3.1. Checking the pipe system 3.2. Adjusting the suction pipes & At home position the inner pipe of the suction pipe protrudes 3.3. Setting the controller F The filling capacity of the hopper loader may not exceed the & The setting is independent of the conveying line and the material & The conveying time which was last selected appears in the & The line clear time which was last selected appears in the display. F If no line clear valve has been installed enter 0". 3.4. Initial conveying operations F This material should not be used again. 3.5. Switching off the unit 4. Error and error correction This chapter is intended for the operating personnel of the & An E appears in the display and an error number. F The control system can only restart operation when the & The cause of the malfunction will not be corrected by pressing F When the malfunction has been corrected press the key. 5. Maintenance L Disconnect the equipment from mains supply before starting F Please observe the maintenance intervals. 5.1. Maintenance intervals F The given maintenance intervals are average values. 5.2. Servicing the conveyor Disconnect the unit from mains supply by the device plug. 5.2.1. Changing the sealing ring of the outlet flap F Observe the direction of installation (G). & Order number sealing ring material outlet: ID 23098 5.2.2. Adjusting the flap switch & Order numbers 5.2.3. Cleaning the unit & Order number & Order numbers 6. Functional description This functional description is intended for all operating personnel Functional description 16 6.1. General 6.2. Controller & The conveying time can be set from 1 to 99 seconds. & An E appears in the display and an error number. 7. Transport, Assembly and Storage This chapter is intended for all operating personnel of the 7.1. Transport and Packing Please ensure adequate carrying capacity of the lifting 7.2. Assembly Please ensure adequate carrying capacity of the lifting 7.3. Storage 8. Assembly instructions These installation instructions are intended for persons with L For installation work taking place at heights of over approx. 6 F Install the equipment such that all parts are easily accessible; this 8.1. Assembly F The controller must be freely accessible. Page 8.2. Mounting on the processing machine 8.3. Mounting onto a machine hopper L Please observe all safety regulations for the operation of welding 8.4. Mounting onto mixing hoppers with lateral inlet 8.5. Mounting onto dosing station DT 30 8.6. Material feed 8.7. Mounting the suction pipe MV F When conveying from silos, material hoppers and storage 8.8. Pipework 8.9. Electrical connection The regulations of the local Electricity Board must be observed. Page 8.9.3. Installation of the alarm indicating device (optional) This work must be carried out by qualified personnel only. & Observe the connecting diagram. 8.10. Compressed-air supply 8.11. Installing the accessories F See chapter Accessories. Page Technical data 32 Page 10. Spare parts list This spare parts list is intended to be used only by trained & Wear Code: Page Spare parts list 36 10.1. SSE-5/BL, 230 V, 50 Hz