SU B-ZE RO BUIL T-IN REF RIGER ATION

BUILT-IN INSTA LL ATIO N

The importance of the installation of the Sub-Zero Built-In unit cannot be overempha- sized. Installation should be done by a qualified installer.

Before you begin the installation process, it is recommended that you read this entire Installa- tion Instructions book. There are key details that you should take special care to observe during the installation. By reading these instructions carefully, you will make the installation process easier, problem-free and, most importantly, safe.

Any questions or problems about the installation should be directed to your Sub-Zero dealer. You can also visit our website at subzero.com.

Important product information, including the model and serial number of your unit are listed on the product rating plate. The rating plate is located at the top frame of the unit inside the door. Refer to the illustration below.

Location of rating plate

Rating plate location

SUB-ZERO®is a registered trademark of Sub-Zero, Inc.

TOOLS AND MATE RI ALS RE QUI RED

The following is a list of tools and materials that should be available for proper installation.

•Phillips screwdriver set

•Slotted screwdriver set

•Torx drive screwdriver set

•1.2 m of 6,35 copper tubing and saddle valve for the water line (4200880)—do not use self- piercing valves

•Copper tubing cutter

•Level—.6 m and 1.2 m recommended

•Appliance Dolly able to support 317 kg and adequate manpower to handle the weight of the unit

•Various sized pliers

•Wrench set

•Allen wrench set

•8 mm hex bolt nut driver

•Crescent wrenches

•Cordless drill and assorted drill bits

•Masonite, plywood, 3,2 mm pressed fiber- board, cardboard or other suitable material to protect finished flooring

•Appropriate materials to cover and protect the home and its furnishings during installa- tion

Make sure that the actual equipment that was shipped to you matches the design you are expecting to install. The Sub-Zero Built-In line offers the following design alternatives— overlay/flush inset and stainless steel models. The overlay/flush inset model has two design applications—overlay and flush inset.

Each of these design options has specific instal- lation requirements, which means it is vital that the unit match your planning and space needs. Before you begin the installation process, check the exact model number you need against the model number on the shipping carton.

If the unit you receive does not match your requirements, contact your Sub-Zero dealer.

SITE PR EPA RAT ION

Make sure that the finished rough opening where the Built-In unit is to be installed is properly prepared. Refer to the Overall Dimen- sions and Installation Specifications for your specific model on the following pages. These specifications are identical for the overlay/flush inset and stainless steel applications. The instal- lation specifications are different for the flush inset application, whether you are using custom panels or Sub-Zero accessory stainless flush inset panels. Make sure that the rough opening dimensions, door swing clearance, electrical service and plumbing are correct for the model you are about to install.

If you are installing two Built-In units side by side in the overlay/flush inset or stainless steel application, a separating filler strip is recom- mended. Add the filler strip width to the finished rough opening dimension. Complete the installa- tion with the Anchoring Kit (7004656). Refer to page 16.

For installation of two Built-In units side by side in the flush inset application, a dual installation kit will be necessary. Refer to page 15.

IMPORTANT NOTE: Built-in units installed side by side in the flush inset application cannot use Sub-Zero accessory stainless flush inset panels, and must have opposing hinges.

IMPORTANT NOTE: To operate properly, the door must open a minimum of 90°. Use a minimum 76 mm filler in corner installations to assure a 90° door opening. Allow enough clear- ance in front of the unit for full door swing.

IMPORTANT NOTE: Make sure the floor under the unit is level with the surrounding finished floor.

As you read these Installation Instructions, take particular note of the CAUTION and WARNING symbols when they appear. This information is important for the safe and efficient installation of Sub-Zero equipment.

CAUTION

signals a situation where minor injury or product damage may occur if you do not follow instructions.

WARNING

states a hazard that may cause serious injury or death if precautions are not followed.

In addition, these Installation Instructions may signal an IMPORTANT NOTE which highlights information that is especially relevant to a problem-free installation.

Page 2 Page 4
Page 3
Image 3
Sub-Zero ICBBI-36R SU B-ZE RO Buil T-IN REF Riger Ation, BUILT-IN Insta LL Atio N, Tools and Mate RI ALS RE QUI RED
Page 2 Page 4

ICBBI-36RG, ICBBI-36F, ICBBI-36R specifications

The Sub-Zero ICBBI-36R, ICBBI-36F, and ICBBI-36RG are premium built-in refrigerators designed to combine cutting-edge technology with sophisticated aesthetics, making them a perfect addition to any modern kitchen. These models stand out for their impressive capacity, advanced features, and customizable design, ensuring they meet the needs of discerning homeowners and culinary enthusiasts alike.

One of the main features of these refrigerators is their dual refrigeration system. By maintaining separate cooling environments for the refrigerator and freezer compartments, Sub-Zero ensures optimal freshness and preservation of food. This technology helps to reduce the chances of odor transfer between compartments, allowing fruits, vegetables, and other perishables to maintain their flavor and nutritional value for longer periods.

The ICBBI-36R model is designed specifically for refrigeration, while the ICBBI-36F focuses on freezing, and the ICBBI-36RG seamlessly combines both. Each unit provides ample storage space, enhancing functionality without compromising on style. The sleek stainless-steel finish and customizable panels enable integration into any kitchen decor, creating a streamlined appearance that suits high-end designs.

Temperature management is a standout characteristic of these units. Sub-Zero refrigerators are equipped with advanced microprocessor controls that monitor and adjust temperatures to ensure optimal conditions for every type of food. The units also feature air purification systems that filter out contaminants and ethylene gas, which can cause fruits and vegetables to ripen too quickly.

Energy efficiency is another critical consideration in these models. Sub-Zero has incorporated energy-saving technologies that meet stringent efficiency guidelines while still delivering superior cooling performance. These refrigerators use less energy than traditional models, aligning with modern consumers' growing interest in sustainability.

Furthermore, the ICBBI-36 line includes various features designed for convenience, such as adjustable shelving and storage bins, providing ease of organization. The door panel ice maker and water dispenser in the ICBBI-36RG model add an extra layer of convenience for users.

Overall, the Sub-Zero ICBBI-36R, ICBBI-36F, and ICBBI-36RG embody a perfect blend of innovation, style, and functionality. With advanced refrigeration technologies, customizable design, and energy efficiency, these models offer a top-tier solution for preserving food while elevating kitchen aesthetics.
Top Page Image Contents