Sub-Zero ICBBI-36F Level the UN IT Overla Y PAN ELS, INS Tall TH E KI Ckpla TE, Grille Trim

BUILT-IN INSTA LL ATIO N INSTRU CTI ON S	OVERLA Y PAN EL INST ALLA TIO N
LEVEL THE UN IT	OVERLA Y PAN ELS

Once the unit is in position, extend the front leveling legs down by turning the legs clockwise and adjust the height. The rear height adjust- ment can be made from the front of the base. Use a 8 mm socket to adjust the rear rollers. Turn the 8 mm hex bolt clockwise to raise the unit or counterclockwise to lower it.

When the unit is leveled properly, or squared off, door and/or drawer adjustments are less likely to be necessary. Refer to the illustration below for location of the rear roller base adjustment.

IMPORTANT NOTE: Be sure to reference leveling of the unit to the floor and not to surrounding cabinetry. This could affect the operation of the unit, such as door closing.

INS TALL TH E KI CKPLA TE

To install, screw the kickplate to brackets attached to the inside surface of each roller base.

IMPORTANT NOTE: The kickplate must be removed for servicing. The floor cannot interfere with removal. Refer to the label mounted on the kickplate support for height clearance.

Reinstall the grille following the instructions on page 8. Turn power back on to the electrical outlet.

If your customer has chosen an overlay design application, make sure that the panels you are about to install match dimensions listed in the Overlay Panel Specifications on page 12.

IMPORTANT NOTE: The overlay panel must fit over the door frame. The weight of each panel assembly cannot exceed 23 kg, 34 kg for Models ICBBI-36R, ICBBI-36RG and ICBBI-36F.

Overlay models are shipped without handle hardware. The cabinet manufacturer or designer will need to provide handle hardware to match the overall decorating scheme.

To install overlay panels, first remove the door trim molding. For side-by-side models and the upper door for over-and-under models, insert a screw- driver tip into the top corner slot on the handle side and pop out the trim molding. Remove the screws and frame. For the drawer on over-and- under models, insert a screwdriver tip into the slot on either side of the trim molding running along the top of the drawer and pop out the trim molding. Remove the screws and frame. Refer to the illustrations below.

Sub-Zero allows a 6 mm space to slide the backing material into place in the frame. If your material is thicker than a 6 mm, either rout an edge around the panel to get a proper fit or mount the decorative overlay panel on a sheet of 6 mm thick material and insert the backing material into the channel.

You must allow for 3 mm space between the backer board and the decorative panel, so the panel will slide easily into the door frame.

The illustrations below provide a cross section view of the three panel assembly showing place- ment of the door/ drawer/grille trim and a rear view of the three panel assembly with critical dimensions, standard for all models.

Install the handle hardware before inserting the panel. We recommend larger D-style pulls. The use of small, one-piece knobs is not recom- mended. If you use screws with thick heads, you will need to countersink the screws into the backer panel before sliding the assembly into place.

Slide the panel into the frame on the door. With the panel in position, replace the frame end. Be sure the panel is inserted completely into the channel for proper fit and alignment.

To reinstall the trim molding on side-by-side models and the upper door for over-and-under models, insert the top of the trim molding into the grooves at the top of the door and work downward, snapping the trim molding into the clips on the frame.

For the drawer on over-and-under models, start at one end and move towards the opposite end, snapping the trim molding into the clips on the frame.

REAR

ADJUSTMENT

FRONT

LEVELING LEG

Rear roller base adjustment Door trim

Spacer Panel
3	Overlay Panel
mm
	6 mm Backer Panel
	8 mm min
	3 mm Door/Drawer/
	2 mm	Grille Trim

Over-and-under drawer trim Overlay panels— cross

section

Overlay Panel	Spacer Panel
~19	Backer
mm	Panel
3 mm	6 mm

Overlay panels—three panel assembly

AC CESSO RIE S

Optional acces- sories are available through your Sub-Zero dealer. To obtain local dealer information, visit our website, subzero.com.

10