Manuals / Subaru / Lawn and Garden / Portable Generator

Subaru R1100 Ac Output Measuring, Measuring Insulation Resistance, Rated voltage, 60Hz-120V

Models: R1100

1 57

Download 57 pages 49.55 Kb

Page 18

Image 18

4-2) AC OUTPUT MEASURING

SWITCH LOAD

TO AC RECEPTACLE	F	V
		~

Use a circuit above for measuring AC output. A hot plate or lamp with a power factor of 1.0 may be used as a load. Adjust the load and rpm, and check that the voltage range is as specified in the following table at the rated amperage and rated rpm.

Rated voltage	60Hz-120V	50Hz-230V	50Hz-240V

Voltage range	120-128	230-246	240-256

4-3) MEASURING INSULATION RESISTANCE

(1)Connect the megger tester across either one of the two output terminals of the AC receptacle and ground

terminal to measure the insulation resistance. Measure it with the AC breaker on. An insulation resistance of 1 MΩor more is normal.

（Original insulation resistance at the time of shipment from the factory is 10 MΩor more.）

If it is less than 1 MΩ, disassemble the generator and measure the insulation resistance of the stator, rotor and control panel individually.

– 15 –

Page 18

Image 18

Subaru R1100 Ac Output Measuring, Measuring Insulation Resistance, Rated voltage, 60Hz-120V, 50Hz-230V, 50Hz-240V, 120-128

Contents

R1100 GENERATORS ModelsPUB-GS2363 Rev. 04/07 Page CONTENTS MODEL 1. SPECIFICATIONS1-1 SPECIFICATIONS R110050Hz 1-2 PERFOMANCE CURVESOUTPUT POWER 50HzFREQUENCY OUTPUT POWER60Hz 1000RECOIL STARTER HANDLE CONTROL PANEL AIR CLEANER FUEL DRAIN SCREW 2. GENERAL DESCRIPTION2-1 EXTERNAL VIEW SIDE PANEL L CARRYING HANDLE TANK CAP COVER SPARK PLUG CAP OIL GAUGESTOP ENGINE SWITCH RUN CHOKE 2-2 CONTROL PANELENGINE SWITCH PILOT LAMP4 AC RECEPTACLES 2 OUTPUT LAMP3 OIL SENSOR LAMP OUT PUT5 DC TERMINALS 6 DC CIRCUIT BREAKER7 AC CIRCUIT BREAKER Serial number and Production number Label 2-3 LOCATION OF SERIAL NUMBER SER No., PRODUCTION NUMBER PROD No2-4 ALTERNATOR Rotor CP3. RANGE OF APPLICATIONS 1 Incandescent lamp, heater, etc. with a power factor of3 Mercury lamps with a smaller power factor 5 Appliances without any indication as to power consumption NOTES Wiring between generator and electrical appliances 4. MEASURING AND CHECKING PROCEDURES 4-1 INSTRUMENTSNOTE Be careful of the frequency meters input voltage range 6 TACHOMETER 4 CIRCUIT TESTER For measuring resistance, etc5 MEAGER TESTER Use the contactless type tacho meter for checking engine speedMODEL Dr.RobinRated voltage 4-2 AC OUTPUT MEASURING4-3 MEASURING INSULATION RESISTANCE 60Hz-120V2 ALTERNATOR 3 CONTROL PANELNOTE When measuring, tolerance should be considered 4-4 CHECKING FUNCTIONAL MEMBERS2 ROTOR ASSEMBLY number variation, ambient temperature etc（3）BRUSH 6 A.V.R AUTOMATIC VOLTAGE REGULATOR 1 Features Checking table for analogue circuit tester Checking table for degital circuit testerAbove the lower level OFFnon-continuity Below the lower level ON continuityOil capacity 0.4 liters Oil Sensor5. ASSEMBLY AND DISASSEMBLY 5-1 PRECAUTIONS5-2 SPECIAL TOOLS 5-3-1 Remove the side panels Left, Right 5-3 DISASSEMBLY PROCEDURES5-3-3 Remove rolling wire, choke wire 5-3-2 Remove the rear cover5-3-5 Remove the control panel NOTE At this point, the couplers of electrical wires are5-3-4 Remove the recoil starter handle connected to the control panel. Instead of5-3-8 Remove fuel cock bracket Engine switch in the off position5-3-7 Remove rear frame NOTE 1 Be sure to close the fuel cock before removing the fuel pipeCouplers 5-3-10 Remove the control panel5-3-11 Remove the fuel pipes Couplers Diode5-3-12 Remove the air cleaner and carburetor 5-3-13 Grounding wire5-3-14 Remove the front frame Tools 12mm Box wrench 5-3-15 Remove the BaseRemove the Base M6 nut 4 pcs, also M8 x 16 Bolt and washer 4pcs 5-3-16 Remove the Brush holder5-3-18 Remove the rotor and Flywheel 5-3-19 Remove Blower housing5-3-17 Remove the Stator / Rear cover NOTE 1 Flywheel can be removed with Rotor at the same time5-3-22 Remove the ignition coil 5-3-20 Remove recoil starter5-3-21 Remove the muffler Recoil starter Muffler Ignition coilM6 x 12mm Flange bolt 1pce Tools 10mm Box wrench 12mm Box wrench 5-3-23 Remove the cylinder baffleRemove the cylinder baffle M8 x 16mm Flange bolt 3pcs By performing the above steps, only a bare engine remainsTightening torque 11.0-13.0 N・m 110-130 kgf・cm 8.1-9.6 ft・lbs 5-4 REASSEMBLY PROCEDURES5-4-1 Cylinder baffle Tightening torque5-4-4 Recoil starter 5-4-6 Air gap adjustment of flywheel and Ignition coilRotor through bolt. Take cake when tightening Tightening torque 7.0-9.0 N・m 70-90 kgf・cm 5.2-6.6 ft・lbsTightening torque 3.0-5.0 N・m 30-50 kgf・cm 2.2-3.7 ft・lbs 5-4-8 Blower housing5-4-7 Ignition coil and harness Tightening torque 18.0-20.0 N・m 180-200 kgf・cm 13.3-14.8 ft・lbs5-4-9 Rear cover, stator NOTE Make sure of the direction of rear cover during installationInstall the Brush holder Tightening torque 10.0-11.0 N・m 100-110 kgf・cm 7.4-8.1 ft・lbs5-4-11 Base 5-4-13 Air cleaner bottom plate and carburetor5-4-14 Air cleaner Tightening torque 18.0-20.0 N・m 180-200 kgf・cm 13.3-14.8 ft・lbs5-4-15 Fuel pipe 5-4-17 Installing coupler5-4-16 Grounding wire Tightening torque 3.0-4.0 N・m 30-40 kgf・cm 2.2-2.9 ft・lbsTightening torque 3.0-4.0 N・m 30-40 kgf・cm 2.2-2.9 ft・lbs 5-4-18 Fuel tank5-4-19 Fuel cock bracket 5-4-20 Rear frameTightening torque 3.0-4.0 N・m 30-40 kgf・cm 2.2-2.9 ft・lbs 5-4-21 Case body, control panelTightening torque 3.0-4.0 N・m 30-40 kgf・cm 2.2-2.9 ft・lbs Tightening torqueswitch into CHOKE position 5-4-23 Choke wire and rolling wireNOTE Make sure the carburetor chock is closed when turning the engine 5-4-24 Rear cover5-5 RECOIL STARTER Please wear protective goggles before starting disassembly1 Disassembly procedures The reel is disassembled with the spring still assembled, so place it on a flat table without dropping, or shakingPlease wear protective goggles before starting assembly 2 Assembly procedure4 Inserting the rope. this should be done by two people 3 Checking items after assembly 4 When 6.TROUBLESHOOTING Replace when wiring is break or damage. Connect properly No DC currentCheck if wiring is break or improper connection Check if DC coil of stator is normal OKEngine does not start Start failure GENERATOR 7. WIRING DIAGRAM50Hz-230V DC coilDC coil 50Hz-240VGENERATOR ENGINEDC coil 60Hz-120VGENERATOR ENGINEPage 940 Lively Blvd. Wood Dale, IL 60191 Phone 630-350-8200 Fax Copyright 2007 Robin America, Inc

4-2) AC OUTPUT MEASURING

Rated voltage

60Hz-120V

50Hz-230V

50Hz-240V

Voltage range

120-128

230-246

240-256

4-3) MEASURING INSULATION RESISTANCE