Manuals / Subaru / Lawn and Garden / Portable Generator

Subaru R1100 Disassembly Procedures, Remove the side panels Left, Right, Remove the rear cover

Models: R1100

1 57

Download 57 pages 49.55 Kb

Page 26

Image 26

5-3) DISASSEMBLY PROCEDURES

Please disassemble in the order of the procedure below.

5-3-1 Remove the side panels (Left, Right)

Remove the side panels.

M6 x 16.5mm Bolt : 2 pcs.

Tools : Screw driver

5-3-2 Remove the rear cover

Remove the rear cover by unscrewing the four screws.

M6 x 20mm Screw and Washer : 4pcs.

Tools : Screw driver

Side Panel

Rear cover

5-3-3 Remove rolling wire, choke wire

Remove chock lever swivel screw fixing chock wire. Untighten adjusting screw nut, remove adjust screw from chock wire bracket, and then take out choke wire from swivel.

Unwind the rolling wire by hand or pliers, and pull up.

Tools : Screw driver, pliers

Adjusting screw
Wire
Nut	Choke wire
Choke wire	Choke wire
	bracket
	Rolling
	wire

– 23 –

Page 26

Image 26

Subaru R1100 service manual Disassembly Procedures, Remove the side panels Left, Right, Remove the rear cover

Contents

PUB-GS2363 Rev. 04/07 R1100 GENERATORSModels Page CONTENTS MODEL 1. SPECIFICATIONS1-1 SPECIFICATIONS R110050Hz 1-2 PERFOMANCE CURVESOUTPUT POWER 50HzFREQUENCY OUTPUT POWER60Hz 1000RECOIL STARTER HANDLE CONTROL PANEL AIR CLEANER FUEL DRAIN SCREW 2. GENERAL DESCRIPTION2-1 EXTERNAL VIEW SIDE PANEL L CARRYING HANDLE TANK CAP COVER SPARK PLUG CAP OIL GAUGESTOP ENGINE SWITCH RUN CHOKE 2-2 CONTROL PANELENGINE SWITCH PILOT LAMP4 AC RECEPTACLES 2 OUTPUT LAMP3 OIL SENSOR LAMP OUT PUT7 AC CIRCUIT BREAKER 5 DC TERMINALS6 DC CIRCUIT BREAKER Serial number and Production number Label 2-3 LOCATION OF SERIAL NUMBER SER No., PRODUCTION NUMBER PROD No2-4 ALTERNATOR Rotor CP3 Mercury lamps with a smaller power factor 3. RANGE OF APPLICATIONS1 Incandescent lamp, heater, etc. with a power factor of 5 Appliances without any indication as to power consumption NOTES Wiring between generator and electrical appliances NOTE Be careful of the frequency meters input voltage range 4. MEASURING AND CHECKING PROCEDURES4-1 INSTRUMENTS 6 TACHOMETER 4 CIRCUIT TESTER For measuring resistance, etc5 MEAGER TESTER Use the contactless type tacho meter for checking engine speedMODEL Dr.RobinRated voltage 4-2 AC OUTPUT MEASURING4-3 MEASURING INSULATION RESISTANCE 60Hz-120V2 ALTERNATOR 3 CONTROL PANELNOTE When measuring, tolerance should be considered 4-4 CHECKING FUNCTIONAL MEMBERS2 ROTOR ASSEMBLY number variation, ambient temperature etc（3）BRUSH 6 A.V.R AUTOMATIC VOLTAGE REGULATOR 1 Features Checking table for analogue circuit tester Checking table for degital circuit testerAbove the lower level OFFnon-continuity Below the lower level ON continuityOil capacity 0.4 liters Oil Sensor5-2 SPECIAL TOOLS 5. ASSEMBLY AND DISASSEMBLY5-1 PRECAUTIONS 5-3-1 Remove the side panels Left, Right 5-3 DISASSEMBLY PROCEDURES5-3-3 Remove rolling wire, choke wire 5-3-2 Remove the rear cover5-3-5 Remove the control panel NOTE At this point, the couplers of electrical wires are5-3-4 Remove the recoil starter handle connected to the control panel. Instead of5-3-8 Remove fuel cock bracket Engine switch in the off position5-3-7 Remove rear frame NOTE 1 Be sure to close the fuel cock before removing the fuel pipeCouplers 5-3-10 Remove the control panel5-3-11 Remove the fuel pipes Couplers Diode5-3-14 Remove the front frame 5-3-12 Remove the air cleaner and carburetor5-3-13 Grounding wire Tools 12mm Box wrench 5-3-15 Remove the BaseRemove the Base M6 nut 4 pcs, also M8 x 16 Bolt and washer 4pcs 5-3-16 Remove the Brush holder5-3-18 Remove the rotor and Flywheel 5-3-19 Remove Blower housing5-3-17 Remove the Stator / Rear cover NOTE 1 Flywheel can be removed with Rotor at the same time5-3-22 Remove the ignition coil 5-3-20 Remove recoil starter5-3-21 Remove the muffler Recoil starter Muffler Ignition coilM6 x 12mm Flange bolt 1pce Tools 10mm Box wrench 12mm Box wrench 5-3-23 Remove the cylinder baffleRemove the cylinder baffle M8 x 16mm Flange bolt 3pcs By performing the above steps, only a bare engine remainsTightening torque 11.0-13.0 N・m 110-130 kgf・cm 8.1-9.6 ft・lbs 5-4 REASSEMBLY PROCEDURES5-4-1 Cylinder baffle Tightening torque5-4-4 Recoil starter 5-4-6 Air gap adjustment of flywheel and Ignition coilRotor through bolt. Take cake when tightening Tightening torque 7.0-9.0 N・m 70-90 kgf・cm 5.2-6.6 ft・lbsTightening torque 3.0-5.0 N・m 30-50 kgf・cm 2.2-3.7 ft・lbs 5-4-8 Blower housing5-4-7 Ignition coil and harness Tightening torque 18.0-20.0 N・m 180-200 kgf・cm 13.3-14.8 ft・lbs5-4-9 Rear cover, stator NOTE Make sure of the direction of rear cover during installationInstall the Brush holder Tightening torque 10.0-11.0 N・m 100-110 kgf・cm 7.4-8.1 ft・lbs5-4-11 Base 5-4-13 Air cleaner bottom plate and carburetor5-4-14 Air cleaner Tightening torque 18.0-20.0 N・m 180-200 kgf・cm 13.3-14.8 ft・lbs5-4-15 Fuel pipe 5-4-17 Installing coupler5-4-16 Grounding wire Tightening torque 3.0-4.0 N・m 30-40 kgf・cm 2.2-2.9 ft・lbsTightening torque 3.0-4.0 N・m 30-40 kgf・cm 2.2-2.9 ft・lbs 5-4-18 Fuel tank5-4-19 Fuel cock bracket 5-4-20 Rear frameTightening torque 3.0-4.0 N・m 30-40 kgf・cm 2.2-2.9 ft・lbs 5-4-21 Case body, control panelTightening torque 3.0-4.0 N・m 30-40 kgf・cm 2.2-2.9 ft・lbs Tightening torqueswitch into CHOKE position 5-4-23 Choke wire and rolling wireNOTE Make sure the carburetor chock is closed when turning the engine 5-4-24 Rear cover1 Disassembly procedures 5-5 RECOIL STARTERPlease wear protective goggles before starting disassembly The reel is disassembled with the spring still assembled, so place it on a flat table without dropping, or shakingPlease wear protective goggles before starting assembly 2 Assembly procedure4 Inserting the rope. this should be done by two people 3 Checking items after assembly 4 When 6.TROUBLESHOOTING Replace when wiring is break or damage. Connect properly No DC currentCheck if wiring is break or improper connection Check if DC coil of stator is normal OKEngine does not start Start failure GENERATOR 7. WIRING DIAGRAM50Hz-230V DC coilDC coil 50Hz-240VGENERATOR ENGINEDC coil 60Hz-120VGENERATOR ENGINEPage 940 Lively Blvd. Wood Dale, IL 60191 Phone 630-350-8200 Fax Copyright 2007 Robin America, Inc