Manuals / Subaru / Lawn and Garden / Portable Generator

Subaru R1100 Fuel tank, Fuel cock bracket, Rear frame, Attach the fuel tank and the fuel cock

Models: R1100

1 57

Download 57 pages 49.55 Kb

Page 41

Image 41

5-4-18 Fuel tank

Attach the fuel tank and the fuel cock.

After the fuel tank is installed, connect the fuel line between fuel cock and fuel pump.

5-4-19 Fuel cock bracket

Install the fuel cock bracket into the base. (Install the rubber pipe with the hose clamp while the fuel cock is closed.)

M6 x 12mm Flange bolt : 1pce.

M6 Nut : 1pce.

Tightening torque : 3.0-4.0 N・m 30-40 kgf・cm (2.2-2.9 ft・lbs)

5-4-20 Rear frame

Attach the rear frame (L) and (R) to the Base.

Fuel tank

Fuel cock bracket

Mounting angle

Base

surface

Front

frame

Rear frame

– 38 –

Page 41

Image 41

Subaru R1100 Fuel tank, Fuel cock bracket, Tightening torque 3.0-4.0 N・m 30-40 kgf・cm 2.2-2.9 ft・lbs, Rear frame

Contents

PUB-GS2363 Rev. 04/07 R1100 GENERATORSModels Page CONTENTS 1-1 SPECIFICATIONS 1. SPECIFICATIONSMODEL R1100OUTPUT POWER 1-2 PERFOMANCE CURVES50Hz 50Hz60Hz OUTPUT POWERFREQUENCY 10002-1 EXTERNAL VIEW 2. GENERAL DESCRIPTIONRECOIL STARTER HANDLE CONTROL PANEL AIR CLEANER FUEL DRAIN SCREW SIDE PANEL L CARRYING HANDLE TANK CAP COVER SPARK PLUG CAP OIL GAUGEENGINE SWITCH 2-2 CONTROL PANELSTOP ENGINE SWITCH RUN CHOKE PILOT LAMP3 OIL SENSOR LAMP 2 OUTPUT LAMP4 AC RECEPTACLES OUT PUT7 AC CIRCUIT BREAKER 5 DC TERMINALS6 DC CIRCUIT BREAKER 2-4 ALTERNATOR 2-3 LOCATION OF SERIAL NUMBER SER No., PRODUCTION NUMBER PROD NoSerial number and Production number Label Rotor CP3 Mercury lamps with a smaller power factor 3. RANGE OF APPLICATIONS1 Incandescent lamp, heater, etc. with a power factor of 5 Appliances without any indication as to power consumption NOTES Wiring between generator and electrical appliances NOTE Be careful of the frequency meters input voltage range 4. MEASURING AND CHECKING PROCEDURES4-1 INSTRUMENTS 5 MEAGER TESTER 4 CIRCUIT TESTER For measuring resistance, etc6 TACHOMETER Use the contactless type tacho meter for checking engine speedDr.Robin MODEL4-3 MEASURING INSULATION RESISTANCE 4-2 AC OUTPUT MEASURINGRated voltage 60Hz-120V3 CONTROL PANEL 2 ALTERNATOR2 ROTOR ASSEMBLY 4-4 CHECKING FUNCTIONAL MEMBERSNOTE When measuring, tolerance should be considered number variation, ambient temperature etc（3）BRUSH 6 A.V.R AUTOMATIC VOLTAGE REGULATOR 1 Features Checking table for degital circuit tester Checking table for analogue circuit testerOil capacity 0.4 liters Below the lower level ON continuityAbove the lower level OFFnon-continuity Oil Sensor5-2 SPECIAL TOOLS 5. ASSEMBLY AND DISASSEMBLY5-1 PRECAUTIONS 5-3-3 Remove rolling wire, choke wire 5-3 DISASSEMBLY PROCEDURES5-3-1 Remove the side panels Left, Right 5-3-2 Remove the rear cover5-3-4 Remove the recoil starter handle NOTE At this point, the couplers of electrical wires are5-3-5 Remove the control panel connected to the control panel. Instead of5-3-7 Remove rear frame Engine switch in the off position5-3-8 Remove fuel cock bracket NOTE 1 Be sure to close the fuel cock before removing the fuel pipe5-3-11 Remove the fuel pipes 5-3-10 Remove the control panelCouplers Couplers Diode5-3-14 Remove the front frame 5-3-12 Remove the air cleaner and carburetor5-3-13 Grounding wire Remove the Base M6 nut 4 pcs, also M8 x 16 Bolt and washer 4pcs 5-3-15 Remove the BaseTools 12mm Box wrench 5-3-16 Remove the Brush holder5-3-17 Remove the Stator / Rear cover 5-3-19 Remove Blower housing5-3-18 Remove the rotor and Flywheel NOTE 1 Flywheel can be removed with Rotor at the same time5-3-21 Remove the muffler 5-3-20 Remove recoil starter5-3-22 Remove the ignition coil Recoil starter Muffler Ignition coilRemove the cylinder baffle M8 x 16mm Flange bolt 3pcs 5-3-23 Remove the cylinder baffleM6 x 12mm Flange bolt 1pce Tools 10mm Box wrench 12mm Box wrench By performing the above steps, only a bare engine remains5-4-1 Cylinder baffle 5-4 REASSEMBLY PROCEDURESTightening torque 11.0-13.0 N・m 110-130 kgf・cm 8.1-9.6 ft・lbs Tightening torqueRotor through bolt. Take cake when tightening 5-4-6 Air gap adjustment of flywheel and Ignition coil5-4-4 Recoil starter Tightening torque 7.0-9.0 N・m 70-90 kgf・cm 5.2-6.6 ft・lbs5-4-7 Ignition coil and harness 5-4-8 Blower housingTightening torque 3.0-5.0 N・m 30-50 kgf・cm 2.2-3.7 ft・lbs Tightening torque 18.0-20.0 N・m 180-200 kgf・cm 13.3-14.8 ft・lbsInstall the Brush holder NOTE Make sure of the direction of rear cover during installation5-4-9 Rear cover, stator Tightening torque 10.0-11.0 N・m 100-110 kgf・cm 7.4-8.1 ft・lbs5-4-14 Air cleaner 5-4-13 Air cleaner bottom plate and carburetor5-4-11 Base Tightening torque 18.0-20.0 N・m 180-200 kgf・cm 13.3-14.8 ft・lbs5-4-16 Grounding wire 5-4-17 Installing coupler5-4-15 Fuel pipe Tightening torque 3.0-4.0 N・m 30-40 kgf・cm 2.2-2.9 ft・lbs5-4-19 Fuel cock bracket 5-4-18 Fuel tankTightening torque 3.0-4.0 N・m 30-40 kgf・cm 2.2-2.9 ft・lbs 5-4-20 Rear frameTightening torque 3.0-4.0 N・m 30-40 kgf・cm 2.2-2.9 ft・lbs 5-4-21 Case body, control panelTightening torque 3.0-4.0 N・m 30-40 kgf・cm 2.2-2.9 ft・lbs Tightening torqueNOTE Make sure the carburetor chock is closed when turning the engine 5-4-23 Choke wire and rolling wireswitch into CHOKE position 5-4-24 Rear cover1 Disassembly procedures 5-5 RECOIL STARTERPlease wear protective goggles before starting disassembly assembled, so place it on a flat table without dropping, or shaking The reel is disassembled with the spring still2 Assembly procedure Please wear protective goggles before starting assembly4 Inserting the rope. this should be done by two people 3 Checking items after assembly 4 When 6.TROUBLESHOOTING Check if wiring is break or improper connection No DC currentReplace when wiring is break or damage. Connect properly Check if DC coil of stator is normal OKEngine does not start Start failure 50Hz-230V 7. WIRING DIAGRAMGENERATOR DC coilGENERATOR 50Hz-240VDC coil ENGINEGENERATOR 60Hz-120VDC coil ENGINEPage Copyright 2007 Robin America, Inc 940 Lively Blvd. Wood Dale, IL 60191 Phone 630-350-8200 Fax