Ok setenv local-mac-address? true | Sun Microsystems 805-1797-10

The mac-addressproperty of the network device speciﬁes the network address (system-wide or local-mac-address) used for booting the system. To start using the MAC addresses assigned to the network interfaces of the Sun Quad FastEthernet PCI adapter, set the NVRAM conﬁguration variable local-mac-address?to true

ok setenv local-mac-address? true

.

Conﬁguring the Driver Software

17

Image 31

Sun Microsystems 805-1797-10 manual Ok setenv local-mac-address? true

Contents

Revision A, August USA 650 960-1300 fax 650 Revision A, August Please Recycle Contents Running Diagnostics Tests Index Regulatory Compliance StatementsPage How This Book Is Organized Preface Related Documents Unix Commands Shell Prompts Typographic Conventions Table P-1SunExpress Contact Information Ordering Sun Documents Xii Sun Welcomes Your CommentsPage 1Sun Quad FastEthernet PCI adapter Product Overview Hardware and Software Requirements Features1Hardware and Software Requirements Displaying the OpenBoot Prom Revision Level Checking the OpenBoot Prom Revision LevelPage Using a text editor, add the following line to the end Installing the AdapterAdding an Entry to the driveraliases File Installing the Adapter Diagnostic Testing Verifying the InstallationExamining Network Activity Code Example 2-1 watch-net-allCommad Output Perform a reconﬁguration boot on the system Rebooting the SystemPage Conﬁguring the Host Files Installing the Driver SoftwareAt the command line, use the grep command to search Conﬁguring the Driver Software Etc/hosts ﬁle Reboot your system Booting From the NetworkAt the ok prompt type As superuser root, type Post-Installation Procedures OptionalConﬁguring Driver Parameters Increasing TCP/IP Performance Type Forcing Network Speed Between 10 Mbps and 100 Mbps Local-mac-address Property Auto-Negotiation Ok setenv local-mac-address? true Page Table A-1Physical Dimensions Speciﬁcations Physical Dimensions Table A-3Performance Speciﬁcations Power RequirementsTable A-2Power Requirements Performance Speciﬁcations Speciﬁcations Page Figure B-132-Pin RJ-45 Connectors Interface SignalsPage Internal Transceiver Conﬁguring the Quad FastEthernet Device Driver Parameters Table C-1qfe Driver Parameter, Status, and Descriptions Driver Parameter Values and Deﬁnitions Qfe Driver Parameter, Status, and Descriptions Deﬁning the Current Status Table C-2Read-Only Parameters Deﬁning the Current Status Inter-Packet Gap Parameters Packet after receiving a packet Table C-4Parameters Deﬁning lancemode and ipg0 Table C-5Operational Mode Parameters Operational Mode Parameters Table C-7Read-Only Transceiver Capabilities Deﬁning the Number of Back-to-Back Packets to TransmitReporting Transceiver Capabilities Table C-6Back-to-back Packet Transmission Capability Table C-8Read-Only Link Partner Capabilities Reporting the Link Partner Capabilities Setting Parameters Using the ndd Utility Setting qfe Driver ParametersTo Specify the Device Instance for the ndd Utility To modify a parameter value, use the -setoption Use the instance number to select the device Using the ndd Utility in Interactive Mode Select at least one of the ﬁve capabilities adv100fdxcap To Set the Mode to Auto-Negotiation Table C-9Setting Variables in the /etc/system File Setting Parameters in the /etc/system File Setting Parameters Using the qfe.conf File Unit-address = 2,1 Fourth line in the previous example Setting ipg Driver Parameters Using a qfe.conf File Kernel/drv/qfe.conf ﬁle Set the ipg1 and ipg2 parameters for the above four devices Using the OpenBoot Prom FCode Selftest Running Diagnostics Tests Shut down the system Reset the systemType show-devsto display the list of devices Reset and reboot the system Set the auto-boot?conﬁguration parameter to truePage FCC Class a Notice Regulatory Compliance Statements FCC Class B Notice DOC Class B Notice Avis DOC, Classe B DOC Class a Notice Avis DOC, Classe a EMC Declaration of Conformity Supplementary Information SafetyPage Index-51 Index