FCC Class B Notice | Sun Microsystems 805-1797-10 manual

Shielded Cables: Connections between the workstation and peripherals must be made using shielded cables in order to maintain compliance with FCC radio frequency emission limits. Networking connections can be made using unshielded twisted-pair (UTP) cables.

Modiﬁcations: Any modiﬁcations made to this device that are not approved by Sun Microsystems, Inc. may void the authority granted to the user by the FCC to operate this equipment.

FCC Class B Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.This device may not cause harmful interference.

2.This device must accept any interference received, including interference that may cause undesired operation.

Note - This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

4receiver is connected.

Consult the dealer or an experienced radio/television technician for help.

Shielded Cables: Connections between the workstation and peripherals must be made using shielded cables in order to maintain compliance with FCC radio frequency emission limits. Networking connections can be made using unshielded twisted pair (UTP) cables.

Modiﬁcations: Any modiﬁcations made to this device that are not approved by Sun Microsystems, Inc. may void the authority granted to the user by the FCC to operate this equipment.

46 Sun Quad FastEthernet PCI Adapter Installation and User's Guide ♦ Revision A, August 1997

Image 60

Sun Microsystems 805-1797-10 manual FCC Class B Notice

Contents

Revision A, August USA 650 960-1300 fax 650 Revision A, August Please Recycle Contents Running Diagnostics Tests Regulatory Compliance Statements IndexPage Preface How This Book Is Organized Unix Commands Related Documents Typographic Conventions Shell Prompts Ordering Sun Documents Table P-1SunExpress Contact Information Sun Welcomes Your Comments XiiPage Product Overview 1Sun Quad FastEthernet PCI adapter Features Hardware and Software Requirements1Hardware and Software Requirements Checking the OpenBoot Prom Revision Level Displaying the OpenBoot Prom Revision LevelPage Installing the Adapter Using a text editor, add the following line to the endAdding an Entry to the driveraliases File Installing the Adapter Verifying the Installation Diagnostic TestingExamining Network Activity Code Example 2-1 watch-net-allCommad Output Rebooting the System Perform a reconﬁguration boot on the systemPage Installing the Driver Software At the command line, use the grep command to searchConﬁguring the Driver Software Conﬁguring the Host Files Etc/hosts ﬁle Booting From the Network Reboot your systemAt the ok prompt type Post-Installation Procedures Optional Conﬁguring Driver ParametersIncreasing TCP/IP Performance As superuser root, type Forcing Network Speed Between 10 Mbps and 100 Mbps Type Auto-Negotiation Local-mac-address Property Ok setenv local-mac-address? true Page Speciﬁcations Physical Dimensions Table A-1Physical Dimensions Power Requirements Table A-2Power RequirementsPerformance Speciﬁcations Table A-3Performance Speciﬁcations Speciﬁcations Page Interface Signals Figure B-132-Pin RJ-45 ConnectorsPage Conﬁguring the Quad FastEthernet Device Driver Parameters Internal Transceiver Driver Parameter Values and Deﬁnitions Table C-1qfe Driver Parameter, Status, and Descriptions Deﬁning the Current Status Qfe Driver Parameter, Status, and Descriptions Inter-Packet Gap Parameters Table C-2Read-Only Parameters Deﬁning the Current Status Table C-4Parameters Deﬁning lancemode and ipg0 Packet after receiving a packet Operational Mode Parameters Table C-5Operational Mode Parameters Deﬁning the Number of Back-to-Back Packets to Transmit Reporting Transceiver CapabilitiesTable C-6Back-to-back Packet Transmission Capability Table C-7Read-Only Transceiver Capabilities Reporting the Link Partner Capabilities Table C-8Read-Only Link Partner Capabilities Setting qfe Driver Parameters Setting Parameters Using the ndd UtilityTo Specify the Device Instance for the ndd Utility Use the instance number to select the device To modify a parameter value, use the -setoption Using the ndd Utility in Interactive Mode To Set the Mode to Auto-Negotiation Select at least one of the ﬁve capabilities adv100fdxcap Setting Parameters in the /etc/system File Table C-9Setting Variables in the /etc/system File Setting Parameters Using the qfe.conf File Setting ipg Driver Parameters Using a qfe.conf File Unit-address = 2,1 Fourth line in the previous example Set the ipg1 and ipg2 parameters for the above four devices Kernel/drv/qfe.conf ﬁle Running Diagnostics Tests Using the OpenBoot Prom FCode Selftest Reset the system Shut down the systemType show-devsto display the list of devices Set the auto-boot?conﬁguration parameter to true Reset and reboot the systemPage Regulatory Compliance Statements FCC Class a Notice FCC Class B Notice DOC Class a Notice Avis DOC, Classe a DOC Class B Notice Avis DOC, Classe B Declaration of Conformity EMC Safety Supplementary InformationPage Index Index-51