TANDBERG GWData port Command Interface User Guide
|
|
| Within ISDN different bearer capabilities are used to signal the type of date | ||
|
|
| (Voice, Data, H320, H324M), which is used by switches and other | ||
|
|
| equipment to determine what to do with the data or the call (compand | ||
|
|
| neglect etc). | ||
|
|
| • IncomingBearerCapability: sets the ISDN bearer capability of | ||
|
|
| the incoming 3G calls. In some situations the non correct UDI | ||
|
|
| bearer is used in stead of the right H324M capability. This setting | ||
|
|
| makes it possible to accept incoming 3G calls both situations.. | ||
|
|
| • OutgoingBearerCapability: sets the ISDN bearer capability for | ||
|
|
| the outgoing 3G calls. In some situations the switch does not | ||
|
|
| accept calls which use the correct H324M capability. This setting | ||
|
|
| makes it possible to use the gateway in these situations (UDI). | ||
|
|
| • BRI SwitchType: Sets the switch type of the gateway in case of a | ||
|
|
| BRI version. | ||
|
|
| • PRI SwitchType: Sets the switch type of the gateway in case of a | ||
|
|
| PRI version. | ||
|
|
| • PRI Interface LowChannel: This parameter sets the lowest | ||
|
|
| channel to start with when making outgoing call (to 3G handsets) | ||
|
|
| Example of ISDN feedback: | ||
|
|
| *c xConfiguration ISDN IncomingBearerCapability: All | ||
|
|
| *c xConfiguration ISDN OutgoingBearerCapability: UDI | ||
|
|
| *c xConfiguration ISDN BRI SwitchType: Euro | ||
|
|
| *c xConfiguration ISDN PRI SwitchType: Euro | ||
|
|
| *c xConfiguration ISDN PRI Interface LowChannel: 1 | ||
|
|
|
| ||
| E1 |
| E1 is the configuration of CRC4 for the ISDN PRI lines. | ||
|
|
| E1 Interface CRC4: <On/Off> |
| |
|
|
| Example of E1 feedback: | ||
|
|
| *c xConfiguration E1 Interface CRC4: Off | ||
|
|
|
| ||
| HTTPS |
| Enables or disables access to HTTPS services. | ||
|
|
| NOTE! Changes become effective after reboot | ||
|
|
| HTTPS Mode <On/Off> | ||
|
|
| Example of HTTPS feedback: | ||
|
|
| *c xConfiguration HTTPS Mode: Off | ||
|
|
|
| ||
| HTTP |
| Enables or disables access to HTTP services. | ||
|
|
| NOTE! Changes become effective after reboot. | ||
|
|
| HTTP Mode <On/Off> | ||
|
|
| Example of HTTP feedback: | ||
|
|
| *c xConfiguration HTTP Mode: On | ||
| SNMP |
| Configures the SNMPmib. | ||
|
|
| Note! For more information about SNMP please read the TANDBERG | ||
|
|
| SNMP application note. | ||
|
|
| SNMP Mode < On/Off/ReadOnly/TrapsOnly > | ||
|
|
| or | ||
|
|
| SNMP CommunityName: <S: 0, 16> | ||
|
|
| or | ||
|
|
| SNMP SystemContact: <S: 0, 70> | ||
|
|
| or | ||
|
|
|
|
|
|
|
|
| 11 |
|
|
