Tascam DP-008 CAUTIONS ABOUT BATTERIES

IMPORTANT SAFETY INFORMATION

CAUTIONS ABOUT BATTERIES

This product uses batteries. Misuse of batteries could cause a leak, rupture or other trou- ble. Always abide by the following precautions when using batteries.

•• Never recharge non-rechargeable batteries. The batteries could rupture or leak, causing fire or injury.

•• When installing batteries, pay attention to the polarity indications (plus/minus (+/–) orientation), and install them correctly in the battery case as indicated. Putting them in backward could make the batteries rupture or leak, causing fire, injury or stains around them.

•• When throwing used batteries away, follow the disposal instructions indicated on the batteries and the local disposal laws.

•• Do not use batteries other than those specified. Do not mix and use new and old batteries or different types of batteries together. The batteries could rupture or leak, causing fire, injury or stains around them.

•• Do not carry or store batteries together with small metal objects. The batteries could short, causing leak, rupture or other trouble.

•• Do not heat or disassemble batteries. Do not put them in fire or water. Batteries could rupture or leak, causing fire, injury or stains around them.

•• If the battery fluid leaks, wipe away any fluid on the battery case before inserting new batteries. If the battery fluid gets in an eye, it could cause loss of eyesight. If fluid does enter an eye, wash it out thoroughly with clean water without rubbing the eye and then consult a doctor immediately. If the fluid gets on a person’s body or clothing, it could cause skin injuries or burns. If this should happen, wash it off with clean water and then consult a doctor immediately.

•• The unit power should be off when you install and replace batteries.

•• Remove the batteries if you do not plan to use the unit for a long time. Batteries could rupture or leak, causing fire, injury or stains around them. If the battery fluid leaks, wipe away any fluid on the battery case before inserting new batteries.

4 TASCAM DP-008

Contents

OWNER'S MANUAL WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE Page CAUTIONS ABOUT BATTERIES Page 11 – Exchanging Data with a Diagram Overview of this unit About this manual Manual conventions Product parts Intellectual property rights About SD cards Precautions for use Cautions on installation Beware of condensation Cleaning the unit Playback and mixing Preparing to listen to the demo song Playing and mixing the demo song Page From recording to creating a master track Creating a new song Connecting and setting the input sources Adjusting the input level and monitoring Recording guitar to TRACK Listening to your recording Record guitar to TRACK Record vocals on TRACK Page Mixing the tracks Mastering the mix Page Page Shutting down the unit Top panel Page Front panel Rear panel Right side panel Bottom panel Home Screen Preparing the power and SD card Installing an SD card Preparing the power Connecting an AC adaptor (sold separately) Start-up& shutdown Starting up the unit Shutting down Formatting SD cards Recorder modes Connecting with other equipment Rear panel connections Right side panel connections Adjusting the contrast Setting the backlight Partitions and songs Selecting the active partition Editing names Loading a saved song Creating a new song Viewing song information Saving a song Copying songs Erasing songs Protecting songs Selecting the input source Phantom power Monitoring input signals About the OL indicators and level meters Using input EQ Assigning inputs Making the first recording Making additional recordings Mixdown Multitrack recording REC indicator settings Track pan and level settings Input selection and assignment Reverb Muting tracks Mastering Setting the end point Recording the master track Undoing operations (undo) Undoing the last operation (single undo) Undoing a previous operation (multi-undo) Erasing the operation history Punching in and out Using the foot switch to punch in/out Setting the foot switch polarity Bouncing tracks Using the bounce function Confirming the result Locate and search functions Direct locate function Fast forward/rewind search Repeat playback Setting IN and OUT points Editing IN/OUT points Using repeat playback Locating to the IN or OUT point Automatically punching in and out Setting the interval between repetitions Rehearsal Using auto punch in/out to record Overview of track editing Editing points Basic editing procedures Explanation of items COPY/PASTE COPY/INSERT MOVE/PASTE MOVE/INSERT OPEN (insert silence) CUT (remove part) SILENCE (part erase) CLEAN out (track erase) Metronome Tuner Chromatic tuner mode Oscillator mode Turning the power off automatically Viewing information Page Overview of partitions Reformatting MTR partitions Reformatting the FAT partition Initializing SD cards Supported operating systems Connecting with a computer Disconnecting Song backup and restoration Backing-upsongs Restoring songs Track import and export Importing tracks Exporting tracks Exporting a stereo master track Why can’t I hear any sound when I play back Why does the sound I'm recording sound distorted Why can’t I record Why can’t my computer “see” the unit files Page Page Audio input/output ratings Audio performance General Optional accessories Computer requirements Backup memory Dimensions Block diagram