Taylor 8752, 8756, 8757 Section 9 Parts Replacement Schedule

43

Models 8752, 8756, 8757 Parts Replacement Schedule

Section 9 Parts Replacement Schedule

PARTDESCRIPTION EVERY3

MONTHS

EVERY4

MONTHS

EVERY6

MONTHS

ANNUALLY QTY.

Scraper Blades X2*

Drive Shaft Seal X1*

Freezer Door Gasket X1*

Front Bearing X1*

Beater Shoes X2*

Draw Valve O- Ring X2**

Prime Plug O- Ring X2*

Pivot Pin O - Ring X1*

Air/Mix Pump O- Ring X4*

Liquid ValveBody Chec k Band X3*

Mix Inlet Fit ting O- Ring X1*

Pressure Switch Diaphragm X1*

Design Cap X1**

White Bristle Brush, 9/16” x 44” Inspect &

Replace if

Necessary

Minimum 1

White Bristle Brush, 1” x 2” Inspect &

Replace if

Necessary

Minimum 1

White Bristle Brush, 3” x 7” Inspect &

Replace if

Necessary

Minimum 1

White Bristle Brush, 3” x 1/2” Inspect & Re-

place if Ne-

cessary

Minimum 1

Small White Bristle Brush Inspect & Re-

place if Ne-

cessary

Minimum 1

Double Ended Brush Inspect&

Replace if

Necessary

Minimum 1

Black Bristle Brush, 1” x 2” Inspect &

Replace if

Necessary

Minimum 1

* Double quantity for Models 8756 and 8757.

** Triple quantity for Models 8756 and 8757.

Refer to Parts List on page 49 when ordering the above parts.

Contents

Main Page Table of Contents Table of Contents - Page 2 Section 1 To the Installer Installer Safety S Site Preparation Air Cooled Units WaterConnections (Water Cooled Units Only) Electrical Connections Beater Rotation Refrigerant Section 2 To the Operator Compressor Warranty Dis claimer Section 3 Safety S Page 8Models 8752, 8756, 8757Operator Parts Identification 8752 Parts Identification Page 10 Models 8752, 8756, 8757Operator Parts Identification 8752 Beater Door Parts Identification Page 12 Models 8752, 8756, 8757Operator Parts Identification 8756 Parts Identification Page 14 Models 8752, 8756, 8757Operator Parts Identification 8757 Parts Identification 15 Models 8752, 8756, 8757 Operator Parts Identification 8756 & 8757 Beater Door Assembly 16 Models 8752, 8756, 8757Operator Parts Identification Accessories Page Parts Identificationfor 8752, 8756, & 8757 Symbol Definitions Power Switch Indicator Lights - MIX LOW and MIX OUT Reset Button SOFTECH Control Operation MIX REF Standby Wash Auto Pump Adjustable Draw Handle Section 6 Operating Procedures Prior to Set- Up (Model 8757) Assembly Page Page Page Air/Mix Pump Assembly Page Page Page Air/Mix Pump Assembly Exploded View Sanitizing Page Priming Closing Procedure S S S S S Draining Product From the Freezing Cylinder Rinsing Cleaning Disassembly Brush Cleaning Check Topping Pump Temperature and Volume - Model 8757 S S S S Section 7 Important: Operator Checklist During Cleaning and Sanitizing Troubleshooting Bacterial Count Regular Maintenance Checks The Air/Mix Pump Winter Storage Section 8 Troubleshooting Guide Page Page Page Page Section 9 Parts Replacement Schedule Section 10 Limited Warranty on Equipment TaylorCompany Section 11 Limited Warranty on Parts Page TaylorCompany Section 12 Parts List Page Page Page Page Page Page Page Page Page Page Page OL SWITCH (SEE FIG. 4) WIRE #11 OF BB POWER/RELAY BOARD BLK BLK HIGH PRESS. CUTOUT 96 95 037808-33 B WIRE #11 OF C0M NO 037808-35 B WIRE #11 OF C0M NO 037808-40 1) STANDBY TEMP. PROBE IS NOT PRESENT ON WIRE #11 OF C0M NO 037808-58 B WIRE #11 OF C0M NO GROUND FRAME SECURELY BLACK T1 BLUE BLACK 037807-33 ENCLOSURES ELECTRICAL 13 ENCLOSURES 037807-40 YEL INTERNAL ENCLOSURES ELECTRICAL ENCLOSURES 042793-27 M FIG 4 MIX PUMP FIG 2 042793-33 GROUND FRAME SECURELY FIG 1 2 6 48 37 26 48 37 8757 042793-34 MM GE MOTOR SCHEMATIC 208/240 50/60 HZ FIG 3 042793-62 GE MOTOR SCHEMATIC BLU/WHT 12 9 85