TABLE OF CONTENTS
3.8.8 Address se
t
ting……………….……………………………………………………………..
Pg. 18
3.8.9 Baud rate se
t
ting…………………………………………………………………………….
Pg. 18
3.9 CONNECTING THE LOAD………………………………………………………………………..
Pg. 19
3.9.1 Load Wi
ing…………………………………………………………………………………..
Pg
. 19
3.9.2 Current CarryingCapa
c
ity………………………………………………………………….
Pg. 19
3.9.3 Wire termination…………………………………………………………………………….
Pg. 20
3.9.4 Noise and Impedance E
f
fects……………………………………………………………...
Pg. 20
3.9.5 Inductive loads………………
……………………………………………………………….
Pg. 20
3.9.6 Making the load conne
c
tions……………………………………………………………….
Pg. 21
3.9.7 Connecting single loads,local sens ing(d
e
fault)…………………………………………
Pg. 24
3.9.8 Connecting single loads, remote sen
s
ing…………………………
……………………...
Pg. 24
3.9.9 Connecting multiple loads, radialdistr ibutionm ethod…………...……………………...
Pg. 24
3.9.10 Multipleloads connection with distribution term
i
nals…………………………………..
Pg. 25
3.9.11 Grounding ou
t
puts………………………………………………………
…………………
Pg. 25
3.10 LOCAL AND REMOTE SENSING………………………………………………………………
Pg. 26
3.10.1 Sensing wi
ing……………………………………………………………………………...
Pg. 26
3.10.2 Local sen
s
ing……………………………………………………………………………….
Pg. 26
3.10.3 Remote sen
s
ing……………………………………
………………………………………
Pg. 27
3.10.4 J2 sense connector technical inform
a
tion………………………………………………
Pg. 27
3.11 REPACKAGING FOR SHIPMENT………………………………………………………………
Pg. 27
CHAPTER4 FRONT AND REARPANEL CONTROLS AND CONNECTORS
………………...
Pg. 28
4.1 INTRODUCT
ION……………………………………………………………………………………
Pg. 28
4.2 FRONT PANEL
CONTROLS AND INDICATORS…………………………………………….
Pg. 28
4.3 REAR PANEL
CONNECTIONS AND CONTROLS…………………………………………..
Pg. 30
4.4 REAR PANEL SW1 SETUP SWITCH……………………………………………………………
Pg. 31
4.4.1 SW1
positions fun
c
tions……………………………………………………………………
Pg. 32
4.4.2 Resetting the switch…………………………………………………………………………
Pg. 32
4.5 REAR PANEL J1 PROGRAMMING AND MONITORING CONNECTOR……………………
Pg. 33
4.5.1 Making J1 conne
c
tions…………………………………………………………………….
.
Pg. 33
CHAPTER5 LOCAL OPERATION
………………………………………………………………….
Pg. 35
5.1 INTRODUCTION…………………………………………………………………………………..
Pg. 35
5.2 STANDARD OPERATION…………………………………………………………………………
Pg. 35
5.2.1 Constant Voltage Mode…………………………………………………………………….
Pg.
35
5.2.2 Constant Current Oper
a
tion………………………………………………………………..
Pg. 35
5.2.3 Automatic Cros
s
over………………………………………………………………………..
Pg. 36
5.3 OVER VOLTAGE PROTECTION (OVP)………………………………………………………...
Pg. 36
5.3.1 Setting the OVPlevel…………………
…………………………………………………….
Pg. 36
5.3.2 Activated OVP protectionindic
a
tions……………………………………………………..
Pg. 36
5.3.3 Resetting the OVP ci
cuit…………….. …………………………………………………...
Pg. 36
5.4 UNDER VOLTAGE LIMIT……………………………………………………………………….. .
Pg. 37
5.4.1 Setting the UVLlevel………………………………………………………………………..
Pg. 37
5.5 FOLDBACK PROTECTION……………………………………………………………………….
Pg. 37
5.5.1 Setting the Foldback prote
c
tion…………………………………………………………….
Pg. 37
5.5.2 Resetting activated Foldback prote
c
tion………
…………………………………………..
Pg. 37
5.6 OUTPUT ON/OFF CONTROL…………………………………………………………………….
Pg. 37
5.7 OUTPUT SHUT
-
OFF (SO) CONTROL VIA REAR PANEL J1 CONNECTOR………………
Pg. 37
5.8 ENABLE/DISABLECONT ROL VIA………………………………………………………………
Pg. 38
5.9 CV/CC SIGNAL……………………………………
………………………………………………..
Pg. 38
5.10 PS OK SIGNAL……………………………………………………………………………………
Pg. 38
5.11 SAFE START AND AUTO
-
RESTART MODES………………………………………………..
Pg. 39
5.11.1 Automatic start mode………………………………………………………………………
Pg. 39
5.11.2 Safe start mode……………
………………………………………………………………..
Pg. 39
5.12 OVER TEMPERATURE PROTECTION (OTP)………………………………………………..
Pg. 39
5.13 LAST SETTING MEMORY………………………………………………………………………
Pg. 39
5.14 SERIES OPERATION…………………………………………………………………………….
Pg. 39
5.14.1 Series connection for
increased output vol
t
age…………………………………………
Pg. 40
5.14.2 Series connection for positive and negativeoutput vol
t
age……………………………
Pg. 41
5.15 PARALLELO PERATION……………………………………………………………………….
Pg. 42