1.Connect this unit and stereo system to a commercially available audio timer.
2.Set the power switch of all components to ON.
3.Load a prerecorded cassette tape in TAPE I or II.
You can also insert tapes into both decks. In this case, TAPE I starts first.
4.Set the REV MODE switch to the required position. If you set the REV MODE switch to 7:
a tape deck plays only Side "A" of the tape.
<If a tape is in both the TAPE I and TAPE II compartments, the TAPE I deck plays Side "A" of the tape and then stops.
If a tape is in the TAPE II compartment only, the TAPE II deck plays Side "A" of the tape.
If you set the REV MODE switch to j:
a tape deck continuously plays both sides of the tape.
When the tape deck reaches the end of Side "A" in playback mode, it automatically reverses the tape and continues to play Side "B".
<If a tape is in both the TAPE I and TAPE II compartments, the TAPE I deck plays both sides of the tape and then stops.
If a tape is in the TAPE II compartment only, the TAPE II deck plays both sides of the tape.
If you set the REV MODE switch to p:
both sides of a tape are continuously played for up to five times.
5.Set the DOLBY NR switch.
6.Set the TIMER switch to the PLAY position.
7.Set the audio timer to the required start (power on) and stop (power off) times. When this setting is completed, the power to all components will be switched off.
When a preset start time is reached, power will be supplied and playback will start automatically.
Playback always starts from side “A”.
NOTE
<If you directly connect the deck’s AC power cord to the AC outlet, playback automatically starts by simply pressing on the POWER switch of this deck when you set the TIMER switch to the PLAY position. When you do not use the timer, set the TIMER switch to the OFF position.
(Example: Recording a broadcast program) |
| |
1. | Connect this unit and stereo system to a commercially |
|
| available audio timer. |
|
2. | Set the power switch of all components to ON. |
|
3. Load a recordable cassette tape(s) in TAPE I or II (or both |
| |
| decks for continuous recording). |
|
4. Set the REV MODE switch to the required position. |
| |
| If you set the REV MODE switch to 7: |
|
| a tape deck records on only Side "A" of the tape. |
|
| < If a tape is in both the TAPE I and TAPE II compartments, the |
|
| TAPE I deck records on Side "A" of the tape and then stops. |
|
| If a tape is in the TAPE II compartment only, the TAPE II deck |
|
| records on Side "A" of the tape. | ENGLISH |
| a tape deck continuously records on both sides of the tape. | |
| If you set the REV MODE switch to j: |
|
When the tape deck reaches the end of Side "A" in record mode, it automatically reverses the tape and continues to record on Side "B".
<If a tape is in both the TAPE I and TAPE II compartments, the TAPE I deck records on both sides of the tape and then stops. If a tape is in the TAPE II compartment only, the TAPE II deck records on both sides of the tape.
If you set the REV MODE switch to p(continuous recording): insert a tape into both the TAPE I and TAPE II compartments. The TAPE I and TAPE II decks continuously record on the tapes.
5.Set the DOLBY NR switch as required.
6.Tune in a broadcasting station to be recorded.
7.Press the RECORD (K) key of the deck to be recorded to set the deck to the
8.Adjust the recording level.
9.Set the TIMER switch to the REC position.
10.Set the audio timer to the required start (power on) and stop (power off) times. When this setting is completed, the power to all components will be switched off.
When the preset start time is reached, power will be supplied and recording will start automatically.
Recording always starts from side “A”.
CAUTION
If you directly connect the deck’s AC power cord to the AC outlet, recording automatically starts by simply pressing on the POWER switch of this deck when you set the TIMER switch to the REC position. When you do not use the timer for a while, be sure to set the TIMER switch back to the OFF position to prevent accidental erasure of your important tape.
21