*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again.
Audio Output (DVD only)
Select the digital output to be output from the optical digital audio output connector of DECK.
1Press ACTION
to display DVD MAIN MENU.
2 | DVD MAIN MENU | Press | ||||
AUDIO OUTPUT |
|
|
| to select | ||
DISC LANGUAGES |
| |||||
|
|
|
|
| ||
ST I L L MODE |
| : AUTO | “AUDIO OUTPUT,” | |||
| TV MODE |
| : 4 : 3 P a n & S c a n | |||
| PROGRESSIVE OUT: OFF | and | ||||
|
|
|
|
|
| |
| SELECT | : |
|
|
| press SET |
| SET | : SET | to display screen. | |||
| END | : ACTION | ||||
|
| |||||
|
|
|
|
| ||
3 | AUDIO OUTPUT | Press | ||||
|
|
| to select an item, | |||
D o l b y D i g i t a l | : B i t s t r e a m |
| ||||
LPCM(DVD) |
| : OFF |
|
| ||
d t s |
| : B i t s t r e a m | and | |||
| DRC |
| : OFF | |||
press SET
Ready Checklist
DECK is in DVD mode, press DVD.
Type of amplifier |
| Recommended setting | ||||||||
to be connected | LPCM | Dolby |
| D T S | ||||||
| ( DV D ) | Digital |
| |||||||
|
|
|
| |||||||
No amplifier is connected |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |
AV amplifier (with digital |
|
|
|
|
|
|
|
|
| |
audio input connector) | P C M | PCM*1 | PCM*1 | |||||||
without Dolby Digital/DTS | ||||||||||
|
|
|
|
|
|
|
|
| ||
decoder |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
AV amplifier including | P C M | Bitstream |
| P C M | ||||||
Dolby Digital decoder |
| |||||||||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |
AV amplifier including | P C M | Bitstream | *2 | |||||||
Dolby Digital/DTS decoder | ||||||||||
Bitstream | ||||||||||
•Make settings according to amplifier connected to optical audio output as shown in above table.
SELECT | : | repeatedly for | |
SET | : SET | output. (See below.) | |
END | : ACTION | ||
|
■“LPCM (DVD)” selections
OFF: Linear PCM of less than 44.1 or 48 kHz/16 bit is output. When playing DVDs recorded in linear PCM of over 44.1 or 48 kHz/20 bit, no digital audio is output. (Factory preset)
PCM: When playing DVDs recorded in linear PCM of
44.1or 48 kHz/20 bit/24 bit or more, digital audio converted to 44.1 kHz/16 bit or 48 kHz/ 16 bit is output.
(Digital output of PCM audio is restricted to 48 kHz/16 bit or below for copyright protection.)
■“Dolby Digital” selections
Bitstream: Dolby Digital bitstream (1 ch - 5.1 ch) is output. (Factory preset)
PCM: When you have connected an amplifier that doesn’t have a
*1 When connecting an amplifier (with an optical digital input connector) which does not contain the Dolby Digital or DTS decoder, be sure to select “PCM”. If “Bitstream” is selected, starting DVD play may cause such a high level of noise as to be harmful to your ears and damage the speakers.
*2 When a dts decoder is connected, please select “Bitstream” in “dts.” If “PCM” is selected, there will be stereo sound.
When a Dolby Digital decoder is connected, please select “Bitstream” in “Dolby Digital.”
If “PCM” is selected, there will be stereo sound.
DVD Operation
■“dts” selections
Bitstream: DTS bitstream is output. (Factory preset)
PCM: When you have connected an amplifier that doesn’t have a
■“DRC (Dynamic Range Compression)”
selections
OFF: Normal audio range is selected. (Factory preset)
ON: For dynamic sound even at low volume, this is useful for
4Press ACTION to redisplay DVD MAIN MENU and go to step 2 to setup another item.
Or, press ACTION twice to exit.
53
