TechniSat ST 6002 S
5 Brief Introduction
We have condensed the most important steps for the installation and use of the ST 6002 S. More detailed information can be found in chapters 6 - 10 of this manual.
It is essential that a high quality outside unit with
5.1Installation
5.1.1 Connection of Outside Unit and TV
Connect your ST 6002 S to the LNB of the outside unit using suitable coaxial cable (eg. TechniSat coaxsat 1750).
LNB
POLARIZER
MOTOR
Pulse
Generator
TV Antennae
Connect the actuator power cable to the M1/M2 sockets and the actuator sensor cable to the "Pulse" and "GND" sockets.
The polariser should be lin- ked via the "Ferrite
To connect your television to the ST 6002 S you should use a euroscart cable. The TV set should be set correspondingly to AV.
TV Antennae
|
|
|
|
|
| EXT BUS |
|
| + FERRIT – |
|
| |
|
|
|
|
|
|
|
|
|
|
| ||
| RF IN |
|
|
|
|
|
|
|
|
|
| F1 |
|
|
|
|
|
|
|
|
|
|
|
| |
| - | + |
| UHF OUT |
|
|
|
|
| 82 ohm, ± 45 mA MAX | 220V | 240V |
|
|
|
|
|
|
|
|
|
|
|
| FUSE |
|
| CH |
|
|
|
|
|
|
|
|
| 250V T500mA |
( | LNB PWR OUT | ( |
|
|
| GND | PULSE | +5V | M2 | M1 |
|
|
DC 14/18V |
|
|
|
|
| |||||||
400 mA MAX |
| EURO SCART FOR VCR/DECODER | EURO SCART FOR TV |
|
|
|
|
|
| |||
|
| I |
|
|
|
|
|
| F2 | |||
|
|
|
|
|
|
|
|
|
|
|
| |
TESTSIGNAL |
| B/G |
|
|
|
|
|
|
| AC 240V 50 Hz |
| |
| TSG |
|
|
|
|
|
|
|
| |||
|
|
|
| ANT IN |
|
|
|
|
| 110 WATTS MAX | FUSE | |
VIDEO |
| VIDEO |
|
|
| 50 mA MAX 36V 1,5 A MAX |
| |||||
|
|
|
|
|
|
|
|
| 250V T500mA | |||
|
|
| DECODER VIDEO |
|
|
|
|
|
|
|
| |
|
|
| Antenna |
| Sensor |
|
|
| Power |
|
| |
|
|
| Cable |
| Cable |
|
|
| Cable |
|
|
Alternatively, you can connect
the appliance to your TV at the UHF/VHF input socket via
UHF antenna cable. If this connection is made you should first of all switch to "TSG" on
the back panel of the ST 6002 S and tune your TV set to channel 36, at which point the test signal (two vertical white stripes) will appear on the screen. Then return the switch to "Video" on the back panel.
NOTE: The satellite receiver is preset to channel 36. If channel 36 is already occupied by a terrestri- al channel it is possible to alter the output channel in the range fom 35 - 44. This can be done using
8