E | displayÖ | and | numbers | If anE Ö | and | a | series | of | numbers appear | in | the display | panel, | there | is | a fault | ||||||
|
|
|
| electronic | system. | Turn | the | appliance off | and | back on | at | the | fuse | or circuit | b | ||||||
|
|
|
| Call customer | service | if the same display appears again. |
|
|
|
|
|
| |||||||||
F | display | and | numbers | If anF and | a | number | flash | in | alternation | on | the displays, | your | appliance | has |
| ||||||
|
|
|
| detected | a | fault. | Refer | to the | following table for possible remedies. |
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
Visual indication |
|
| Fault |
|
|
|
|
| Measure |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
F0 |
|
|
|
| An | internal error | was Disconnect | the | appliance from the | power |
|
| |||||||||
|
|
|
|
| produced | while | the |
| source. Wait a | few seconds | before | connecting | it | ||||||||
|
|
|
|
| cooktop | was | working.again. |
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
| If the symbol appears again, call customer |
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
| service. |
|
|
|
|
|
|
|
|
|
F2
F4
F8
o1
o2/o3
U400
The element is too hotRemove | the pans from the elementsF2 . | |||||||||||||
and | has | turned | off. |
| disappears |
| when you acknowledge the display | |||||||
|
|
|
|
|
| (by pressing a touch key) and the element has | ||||||||
|
|
|
|
|
| cooled sufficiently. Wait a few minutes until the | ||||||||
|
|
|
|
|
| elements have cooled down slightlyF2. If | ||||||||
|
|
|
|
|
| appears | again | after the | element is turned back | |||||
|
|
|
|
|
| on, the cooktop is still too hot. Turn off the | ||||||||
|
|
|
|
|
| elements and | allow them to | cool further. | ||||||
|
|
|
|
|
| |||||||||
The pot or pan is tooVerify that |
| the pot or pan is properly positioned | ||||||||||||
close to | the | control |
| on the | element. Verify that nothing hot is on the | |||||||||
panel. |
|
|
|
| touch key |
| panel. Remove the hot item from the | |||||||
|
|
|
|
|
| control | area. | Wait a few minutes for the touch | ||||||
|
|
|
|
|
| key panel to coolF4. Ifappears again after the | ||||||||
|
|
|
|
|
| element | is | turned back | on, | call customer service. | ||||
|
|
|
|
|
|
|
|
|
|
| ||||
The | element | has | beenThe | automatic | shut off | was | activated. | |||||||
in constant operation Turn the | element off. |
|
|
| ||||||||||
for | too long. |
|
|
| You | can | turn | it back on again immediately. | ||||||
|
|
|
|
|
|
| ||||||||
The | power voltage is Turn | off the | cooktop. Wait a few seconds before | |||||||||||
too | low. |
|
|
|
| turning | it | back on. |
|
|
| |||
|
|
|
|
|
| If the indication continues, contact your | ||||||||
|
|
|
|
|
| electricity | supplier. |
|
|
| ||||
|
|
|
|
|
|
|
| |||||||
The | element | has |
|
| It has | been automatically deactivated to protect | ||||||||
overheated. |
|
|
| your | cooktop. |
|
|
|
| |||||
|
|
|
|
|
| Wait | a | few | minutes for | it to cool down and swi | ||||
|
|
|
|
|
| it back | on | again. |
|
|
| |||
|
|
|
|
|
|
|
|
| ||||||
The | cooktop | is |
|
| Disconnect |
| the appliance from the power source | |||||||
connected | incorrectly. at the | circuit breaker or fuse. Check the | ||||||||||||
|
|
|
|
|
| connection |
| and connect it again correctly. | ||||||
|
|
|
|
|
| If U400 | appears again, call customer service. | |||||||
21
