10.Heater Location
Use the clearances in Paragraph 8; the combustion air requirements in Paragraph 9; the mounting height requirements, throw information, sound data, and location rec- ommendations below; the weights in Paragraph 11; and the venting requirements in Paragraph 24 to determine where to suspend the heater.
Mounting Height
Heater Throw - All Models
CAUTION: Do not locate the heater where it may be exposed to water spray, rain, or dripping water.
Locate the heater so that it is a minimum of 15 feet (4.6M) above the floor and in compliance with the clearances in Paragraph 8.
WARNING: If touched, the vent pipe and internal heater surfaces that are accessible from outside the heater will cause burns. Suspend the heater a minimum of 15 feet (4.6M) above the floor.
FIGURE 3 - Model LDAP Air Throw (Heat Mode @ High Speed) - Applies to All Sizes
Mounting | 30° Nozzle | 60° Nozzle | |
Height |
| Standard Louvers |
|
| X | 0 |
|
Standard |
|
| |
Y |
|
| |
Louvers |
|
| |
Z |
|
| |
|
|
| |
30° Nozzle | X |
|
|
Y |
|
| |
| Z |
|
|
60° Nozzle | X |
|
|
Y |
|
| |
| Z | 0 = “Rear” of Heater Discharge |
|
|
|
|
NOTES:
•X = Distance from “0” to beginning of floor coverage.
•Y = Distance from “0” to end of floor coverage.
•Length of floor coverage = Y - X.
•Z = Distance from “0” to the point where the air velocity drops below 50 feet (15.2M) per minute.
•Throws listed are with standard louvers facing one direction and fully open. Throw pattern changes with louver angle,
Throw (feet and meters)
Mounting Height | (feet) | Standard Louvers | Throw (feet) | 60° Degree Nozzle | ||||||
|
| 30° Degree Nozzle | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| X | Y | Z | X | Y | Z | X | Y | Z |
|
|
|
|
|
|
|
|
|
|
|
20 |
| 5 | 55 | 134 | 40 | 90 | 146 | 70 | 125 | 158 |
30 |
| 8 | 53 | 121 | 44 | 86 | 133 | 76 | 119 | 145 |
40 |
| 12 | 49 | 109 | 47 | 81 | 120 | N/A | N/A | N/A |
50 |
| 17 | 45 | 96 | N/A | N/A | N/A | N/A | N/A | N/A |
|
|
|
|
|
|
|
|
| ||
Mounting Height | (Meters) | Standard Louvers | Throw (meters) | 60° Degree Nozzle | ||||||
|
| 30° Degree Nozzle | ||||||||
|
| X | Y | Z | X | Y | Z | X | Y | Z |
|
|
|
|
|
|
|
|
|
|
|
6.1 |
| 1.5 | 16.8 | 40.8 | 12.2 | 27.4 | 44.5 | 21.3 | 38.1 | 48.2 |
9.1 |
| 2.4 | 16.2 | 36.9 | 13.4 | 26.2 | 40.5 | 23.2 | 36.3 | 44.2 |
12.2 | 3.7 | 14.9 | 33.2 | 14.3 | 24.7 | 36.6 | N/A | N/A | N/A | |
15.2 | 5.2 | 13.7 | 29.3 | N/A | N/A | N/A | N/A | N/A | N/A |
Form