Unlocking programs temporarily | Toshiba 56HM66, 50HM66 specs

HM66_EN.book Page 38 Thursday, February 23, 2006 2:49 PM

Chapter 5: Using the TV’s basic features

Unlocking programs temporarily

If you try to tune the TV to a program that exceeds the rating limits you set, the TV will enter program lock mode and the following message will appear on-screen:

This program exceeds the rating limit you set.

Push 'mute' to enter PIN.

You can either temporarily unlock the program or select an unlocked program to watch.

To temporarily unlock the program:

1 Press W.

2 Enter your four-digit PIN code and press T. If the correct code is entered, the program lock mode is released and the normal picture appears. All locking is disabled until the TV is turned off, and will be enabled when the TV is turned on again.

Locks	Active

Enter PIN code to temporaily un-

block.

* * * *

Cancel Done

Using the input lock feature

You can use the Input Lock feature to lock the video inputs (VIDEO 1, VIDEO 2, ColorStream HD-1, ColorStream HD-2, HDMI 1, and HDMI 2) and channels 3 and 4. You will not be able to view the input sources or channels until you unlock the inputs.

To lock/unlock the video inputs:

1 Press Yand highlight the Locks menu icon.

2 Press b to display the PIN code entering screen.

3 Enter your four-digit PIN code and press T.

4 Press b to highlight Input Lock and press c.

5 Press B or b to select the level of video input locking you prefer, as described below.

Video: Locks VIDEO 1, VIDEO 2, ColorStream HD1/ HD2, HDMI 1/HDMI 2.

Video+: Locks VIDEO 1, VIDEO 2, ColorStream HD1/ HD2, HDMI 1/HDMI 2, and channels 3 and 4.

•Select Video+ if you play video tapes via an ANT input.

•When a CableCARD™ is inserted, Video+ will not lock channels 3 and 4.

Locks

	Enable Rating Blocking			Off				Off
	Edit Rating Limits							Video
	Channels Block							Video +
	Input Lock			Off

	Front Panel Lock			Off

	New PIN Code

	Navigate ENTER Select			MENU Back				EXIT Exit

Off: Unlocks all video inputs and channels 3 and 4.

6 Press T.

38

HM66 (E/F) Web 213:276

Image 38

Toshiba 56HM66, 50HM66 Unlocking programs temporarily, Using the input lock feature, To temporarily unlock the program

Contents

50HM66 56HM66 Trademark Information Voice announce featureWelcome to Toshiba Television Stand Model 50HM66 ST5066 56HM66 ST5666 Contents Features of your new TV Introduction Blue, Yellow and Green/Red LEDs TV front and side panel controls and connectionsControl panel ColorStream HD-1, ColorStream HD-2, Hdmi 1, Hdmi 2, ANT TV back panel connections ColorStream HD-1 and ColorStream HD-2 Installing the remote control batteries Using the remote controlPreparing the remote control for use Remote control effective range Learning about the remote control TheaterWide 1/2/3, and Full CH Bb Using the remote control to control your other devicesTo use your TV remote control to operate a Remote Control functional key chart VCR DVD Programming the remote control to control your other devices TV/VCR Combo Cable converter boxSatellite receiver DVD/VCR Combo Htib Icon Option Menu layout and navigationMain menu layout Installation Setup/Installation menu layoutSetup menu Navigating the menu system Selecting the menu language Setting up your TVTo configure the ANT 1 and ANT 2 input sources To select the menu language To program channels automatically Programming channels automaticallyManually adding and deleting channels in the channel memory To add or delete channels in the channel memory Programming your favorite Channels To tune your favorite channels for the current ANT input To program favorite channels for another inputTo clear your favorite channel lists Setting the Quick Restart feature Setting the ColorStream HD audio modeSetting the Hdmi audio mode Viewing the CableCARD menu To view the digital signal meter Viewing the digital signal meterTo set the Quick Restart feature To close the screen and return to the Terrestrial menu To cancel the reset To close the screen and return to the Installation menuRestore Factory Defaults Viewing the system status Labeling the video input sources Using the TV’s basic featuresSelecting the video input source to view To select the video input source to view Input labeling example Tuning channelsUsing the Channel Browser To clear the input labels Elements of the Channel Browser banner Switching between two channels using Channel Return Tuning your favorite channelsTuning to a specific channel programmed or unprogrammed Switching between two channels using SurfLock Natural picture size Selecting the picture sizeTo select the picture size TheaterWide 1 picture size For 43 format program To set the scroll settings Full picture size for 169 480i, 480p source programs only To turn off the auto aspect ratio feature Signal Selected when Auto Aspect is On SourceTo turn on the auto aspect ratio feature To set the Cinema Mode to Video Adjusting the picture quality Adjusting the pictureSelecting the picture mode Mode Picture Quality To view captions or text Using the closed caption modeClosed Caption Advanced To customize the closed captions Digital closed captions Adjusting the audioUsing the digital audio selector Muting the sound Selecting stereo/SAP broadcasts Adjusting the audio qualityTo adjust the audio quality To listen to stereo sound Selecting the optical audio output format Using the StableSound featureTurning off the built-in speakers If you cannot remember your PIN code Using the Locks menuEntering the PIN code Changing your PIN code Blocking TV programs and movies by alternate ratings Blocking TV programs and movies by rating V-ChipTo block and unblock TV programs and movies TV-14 To unblock individual channels Blocking channelsTo block channels To block all channels at once To temporarily unlock the program Using the input lock featureUnlocking programs temporarily To lock/unlock the video inputs Setting the sleep timer Using the control panel lock feature To display TV setting information on-screen Understanding the auto power off featureUnderstanding the last mode memory feature To close the Recall screen Using dynamic contrast Using the TV’s advanced featuresUsing the advanced picture settings features Using CableClear/DNR digital noise reduction To select the color temperature Selecting the color temperatureSelecting the lamp mode To select the lamp mode Using the SRS WOW surround sound feature Using the advanced audio settings featuresUsing the Game Mode feature Troubleshooting General troubleshooting Channel tuning problems Sound problemsRemote control problems Closed caption problems LED Indication Condition Solution Voice Announce LED indications Appendix Lamp unit replacement and careWhen to replace the lamp unit Canada How to replace the lamp unit Required tools Replace the screw and tighten using a manual screwdriver Disposing of the used lamp unit Specifications Limited United States Warranty For DLP Television Models Limited Canada Warranty How to Obtain Warranty Services HM66EN.book Page 53 Thursday, February 23, 2006 249 PM Index Wowsrs 3D HM66EN.book Page 55 Thursday, February 23, 2006 249 PM 06-03