Manuals / Toshiba / Computer Equipment / Network Card

Toshiba AS311 RS-232C/RS-422 selection switches for channel, RSW1/RSW2  Optional rotary switches

Models: AS311

1 66

Download 66 pages 63.98 Kb

Page 14

RS-232C/RS-422 selection switches (for channel 1)

1. AS311 Overview

SW3 

1

2

3

RS-232C/RS-422 selection switches (for channel 1)

					Used to select the interface of the channel 1 either


					RS-232C or RS-422.
					RS-232C or RS-422.
					No.1		OFF	ON
					No.1		OFF	ON
					Interface		RS-232C	RS-422
					Interface		RS-232C	RS-422
					Used to connect the terminating resistor (120 Ω )




					between RXDA and RXDB. (Effective for RS-422)
	ON→				between RXDA and RXDB. (Effective for RS-422)
	ON→				No.2		OFF	ON


	SW3				Terminating		Not connect	Connect

Used to connect the terminating resistor (120 Ω ) between CTSA and CTSB. (Effective for RS-422)

No.3	OFF	ON
Terminating	Not connect	Connect

NOTE The switches No.2 and No.3 should be set to ON when the AS311 is configured as terminal station on the RS-422 transmission line. The factory settings of the SW3 are all OFF.

RSW1/RSW2  Optional rotary switches

RSW1

RSW2

C

8 0

4 C

80

4

Always set the RSW1 to 4 and the RSW2 to 0. (Other settings are for future use)

Do not set other than above, otherwise the AS311 will not work correctly.

12 ASCII Interface Module (AS311)

Image 14

Toshiba RS-232C/RS-422 selection switches for channel, RSW1/RSW2  Optional rotary switches, 1. AS311 Overview, No.1

Contents

AS311 TOSHIBA CORPORATIONPROGRAMMABLE CONTROLLER ASCII INTERFACE MODULEImportant Information HINT Safety PrecautionsSymbols Used In This Manual Safety PrecautionsSection 5 Operation Procedure Section 2 SpecificationsSection 4 Register Configuration About This ManualTerminology T-PDS Ver. 1.4 Command Reference ManualRelated Manuals T3 User’s Manual - HardwareContents ContentsContents 6 ASCII Interface Module AS311 1.1 Introduction 1.2 AS311 functions 1.3 External features Section AS311 Overview1. AS311 Overview 1.1 Introduction1.2 AS311 functions 1. AS311 Overview1. AS311 Overview 1.3 External featuresAS311 Status LEDs SW1  channel 1 transmission parameter setting switchesSW2  channel 2 transmission parameter setting switches No.71. AS311 Overview RS-232C/RS-422 selection switches for channelRSW1/RSW2  Optional rotary switches No.11. AS311 Overview Hardware reset switchChannel 1 and channel 2 serial ports 14 ASCII Interface Module AS311 2.3 Transmission specifications Section Specifications2.1 General specifications 2.2 Functional specifications 2.2 Functional specifications 2. Specifications2.1 General specifications 2.3 Transmission specifications 2. Specifications18 ASCII Interface Module AS311 Section Cable Connections 3.1 RS-232C connection 3.2 RS-422 connection1 FG 2 TXD 3 RXD 4 RTS 5 CTS 6 DSR 7 SG 20 DTR 3. Cable Connections3.1 RS-232C connection RXD TXD DTR SG DSR RTS CTS3.2 RS-422 connection 3. Cable Connections22 ASCII Interface Module AS311 Section Register Configuration 4.1 I/O allocation and I/O registers 4.2 AS311 buffer memory4. Register Configuration 4.1 I/O allocation and I/O registers4. Register Configuration 4. Register Configuration 4.2 AS311 buffer memory4.2.1 Memory map Status and command4. Register Configuration 4.2.2 Buffer memory accessREAD instruction FUN237 WRITE instruction FUN238 4. Register Configuration4.2.3 Parameter area 4. Register ConfigurationRSW1/2 information Status and command 0Status 1 4. Register Configuration4. Register Configuration SW1 informationSW2 information 4. Register Configuration Command 1CH1 receive error 16 and CH2 receive error 4. Register Configuration CH1 transmit error 17 and CH2 transmit errorCH1 channel status 18 and CH2 channel status 4. Register Configuration CH1 receive length 19 and CH2 receive lengthCH1 trailing code 24 and CH2 trailing code CH1 time-out check 25 and CH2 time-out check 4. Register Configuration4.2.4 Receiving and transmitting data area 4. Register Configuration5.7 Setting the time-out check time Section Operation Procedure5.5 Resetting the AS311 by software 5.6 Setting the trailing code 5.1 Transmission message format 5.2 Received message read sequence5. Operation Procedure 5.1 Transmission message format5.2 Received message read sequence 5.2.1 Flag control timing 5. Operation ProcedureOperation for receiving error Subroutine No 5.2.2 T3 sample program for message receiving5. Operation Procedure Main program Operation for normal received message5. Operation Procedure 5. Operation Procedure Explanation for this sample program5.3 Write sequence for message transmitting 5.3.1 Flag control timing 5. Operation ProcedureD0200 - D0263, and set R0110 to ON Operation for transmitting error 5.3.2 T3 sample program for message transmitting5. Operation Procedure Main program Set the transmission message into5. Operation Procedure 5. Operation Procedure 5.4 Checking the AS311 operation status 5. Operation Procedure5.5 Resetting the AS311 by software 5. Operation ProcedureH0003 5.6 Setting the trailing code5. Operation Procedure H80FE5.7 Setting the time-out check time 5. Operation Procedure6.1 LED indication 6.2 Buffer memory information 6.3 Trouble shooting Section RAS Information6. RAS Information 6.1 LED indication6. RAS Information 6.2 Buffer memory information6.2.1 Module status 6.2.2 Switch setting status 6. RAS Information6.2.3 Error information for data receiving 6. RAS Information6.2.4 Error information for data transmitting 6. RAS Information6.3 Trouble shooting 6. RAS Information58 ASCII Interface Module AS311 Appendix A.1 Specification of the READ instructionA.2 Specification of the WRITE instruction Function A.1 Specification of the READ instructionAppendix OperandAppendix Function A.2 Specification of the WRITE instructionAppendix OperandAppendix TOSHIBA CORPORATION Industrial Equipment Department