Manuals / Toshiba / Computer Equipment / Network Card

Toshiba AS311 user manual Safety Precautions, Symbols Used In This Manual, Hint

Models: AS311

1 66

Download 66 pages 63.98 Kb

Page 3

Safety Precautions

Safety Precautions

Safety Precautions

•This module (AS311) has been designed for Toshiba’s Programmable Controller PROSEC-T3 (hereafter called T3). Use this module only on the T3’s rack.

•Read the Safety Precautions described on the T3 User’s Manual before using the T3 and this module.

•Follow the instructions described on this manual and on the T3 User’s Manual when installing and wiring the T3 and this module.

•Do not touch the connector pins or components on the printed circuit board of this module.

•The maximum number of AS311s that can be controlled by one T3 is not limited by software. However, this module consumes maximum 1 A of internal 5 Vdc power. Confirm that the total 5 Vdc consumed current per one power supply module is within the limit (7A).

Symbols Used In This Manual

Pay attention to information preceded by the following symbols.

HINT

NOTE

Refers to helpful suggestions on how to operate effectively.

Refers to information considered essential for full understanding of operation. And refers to conditions that could damage the equipment or render it temporarily inoperative.

User’s Manual

1

Image 3

Toshiba AS311 user manual Safety Precautions, Symbols Used In This Manual, Hint

Contents

ASCII INTERFACE MODULE TOSHIBA CORPORATIONPROGRAMMABLE CONTROLLER AS311Important Information Safety Precautions Safety PrecautionsSymbols Used In This Manual HINTAbout This Manual Section 2 SpecificationsSection 4 Register Configuration Section 5 Operation ProcedureT3 User’s Manual - Hardware T-PDS Ver. 1.4 Command Reference ManualRelated Manuals TerminologyContents ContentsContents 6 ASCII Interface Module AS311 Section AS311 Overview 1.1 Introduction 1.2 AS311 functions 1.3 External features1.1 Introduction 1. AS311 Overview1. AS311 Overview 1.2 AS311 functions1.3 External features AS3111. AS311 Overview No.7 SW1  channel 1 transmission parameter setting switchesSW2  channel 2 transmission parameter setting switches Status LEDsNo.1 RS-232C/RS-422 selection switches for channelRSW1/RSW2  Optional rotary switches 1. AS311 OverviewHardware reset switch Channel 1 and channel 2 serial ports1. AS311 Overview 14 ASCII Interface Module AS311 Section Specifications 2.1 General specifications 2.2 Functional specifications2.3 Transmission specifications 2. Specifications 2.1 General specifications2.2 Functional specifications 2. Specifications 2.3 Transmission specifications18 ASCII Interface Module AS311 3.1 RS-232C connection 3.2 RS-422 connection Section Cable ConnectionsRXD TXD DTR SG DSR RTS CTS 3. Cable Connections3.1 RS-232C connection 1 FG 2 TXD 3 RXD 4 RTS 5 CTS 6 DSR 7 SG 20 DTR3. Cable Connections 3.2 RS-422 connection22 ASCII Interface Module AS311 4.1 I/O allocation and I/O registers 4.2 AS311 buffer memory Section Register Configuration4.1 I/O allocation and I/O registers 4. Register Configuration4. Register Configuration Status and command 4.2 AS311 buffer memory4.2.1 Memory map 4. Register Configuration4.2.2 Buffer memory access READ instruction FUN2374. Register Configuration 4. Register Configuration WRITE instruction FUN2384. Register Configuration 4.2.3 Parameter area4. Register Configuration Status and command 0Status 1 RSW1/2 informationSW1 information SW2 information4. Register Configuration Command 1 CH1 receive error 16 and CH2 receive error4. Register Configuration CH1 transmit error 17 and CH2 transmit error CH1 channel status 18 and CH2 channel status4. Register Configuration CH1 receive length 19 and CH2 receive length CH1 trailing code 24 and CH2 trailing code4. Register Configuration 4. Register Configuration CH1 time-out check 25 and CH2 time-out check4. Register Configuration 4.2.4 Receiving and transmitting data area5.1 Transmission message format 5.2 Received message read sequence Section Operation Procedure5.5 Resetting the AS311 by software 5.6 Setting the trailing code 5.7 Setting the time-out check time5.1 Transmission message format 5. Operation Procedure5. Operation Procedure 5.2 Received message read sequence 5.2.1 Flag control timingMain program Operation for normal received message 5.2.2 T3 sample program for message receiving5. Operation Procedure Operation for receiving error Subroutine No5. Operation Procedure Explanation for this sample program 5. Operation Procedure5. Operation Procedure 5.3 Write sequence for message transmitting 5.3.1 Flag control timingMain program Set the transmission message into 5.3.2 T3 sample program for message transmitting5. Operation Procedure D0200 - D0263, and set R0110 to ON Operation for transmitting error5. Operation Procedure 5. Operation Procedure 5. Operation Procedure 5.4 Checking the AS311 operation status5. Operation Procedure 5.5 Resetting the AS311 by softwareH80FE 5.6 Setting the trailing code5. Operation Procedure H00035. Operation Procedure 5.7 Setting the time-out check timeSection RAS Information 6.1 LED indication 6.2 Buffer memory information 6.3 Trouble shooting6.1 LED indication 6. RAS Information6.2 Buffer memory information 6.2.1 Module status6. RAS Information 6. RAS Information 6.2.2 Switch setting status6. RAS Information 6.2.3 Error information for data receiving6. RAS Information 6.2.4 Error information for data transmitting6. RAS Information 6.3 Trouble shooting58 ASCII Interface Module AS311 A.1 Specification of the READ instruction A.2 Specification of the WRITE instructionAppendix Operand A.1 Specification of the READ instructionAppendix FunctionAppendix Operand A.2 Specification of the WRITE instructionAppendix FunctionAppendix Industrial Equipment Department TOSHIBA CORPORATION