Manuals / Toshiba / Computer Equipment / Network Card

Toshiba AS311 user manual Cable Connections, 3.1 RS-232C connection, Rxd Txd Dtr Sg Dsr Rts Cts

Models: AS311

1 66

Download 66 pages 63.98 Kb

Page 22

3. Cable Connections

3. Cable Connections

3.1 RS-232C connection

The following figure shows the RS-232C connection.

AS311

Shielded cable

RS-232C device

1 FG

2TXD

3RXD

4RTS

5CTS

6(DSR)

7SG

20DTR

RXD TXD DTR SG DSR RTS CTS

(1)DSR is supported only on the channel 2.

(2)Connect SG each other.

(3)Use shielded cable. The cable shield should be connected to FG at one end.

(4)It is recommended to use twisted cable for noise immunity.

NOTE	Do not connect or remove the connector while the AS311 is powered. Otherwise, it
	will cause damage to the AS311.

20 ASCII Interface Module (AS311)

Image 22

Toshiba AS311 user manual Cable Connections, 3.1 RS-232C connection, 1 FG 2 TXD 3 RXD 4 RTS 5 CTS 6 DSR 7 SG 20 DTR

Contents

AS311 TOSHIBA CORPORATIONPROGRAMMABLE CONTROLLER ASCII INTERFACE MODULEImportant Information HINT Safety PrecautionsSymbols Used In This Manual Safety PrecautionsSection 5 Operation Procedure Section 2 SpecificationsSection 4 Register Configuration About This ManualTerminology T-PDS Ver. 1.4 Command Reference ManualRelated Manuals T3 User’s Manual - HardwareContents ContentsContents 6 ASCII Interface Module AS311 1.1 Introduction 1.2 AS311 functions 1.3 External features Section AS311 Overview1. AS311 Overview 1.1 Introduction1.2 AS311 functions 1. AS311 OverviewAS311 1.3 External features1. AS311 Overview Status LEDs SW1  channel 1 transmission parameter setting switchesSW2  channel 2 transmission parameter setting switches No.71. AS311 Overview RS-232C/RS-422 selection switches for channelRSW1/RSW2  Optional rotary switches No.1Channel 1 and channel 2 serial ports Hardware reset switch1. AS311 Overview 14 ASCII Interface Module AS311 2.1 General specifications 2.2 Functional specifications Section Specifications2.3 Transmission specifications 2.1 General specifications 2. Specifications2.2 Functional specifications 2.3 Transmission specifications 2. Specifications18 ASCII Interface Module AS311 Section Cable Connections 3.1 RS-232C connection 3.2 RS-422 connection1 FG 2 TXD 3 RXD 4 RTS 5 CTS 6 DSR 7 SG 20 DTR 3. Cable Connections3.1 RS-232C connection RXD TXD DTR SG DSR RTS CTS3.2 RS-422 connection 3. Cable Connections22 ASCII Interface Module AS311 Section Register Configuration 4.1 I/O allocation and I/O registers 4.2 AS311 buffer memory4. Register Configuration 4.1 I/O allocation and I/O registers4. Register Configuration 4. Register Configuration 4.2 AS311 buffer memory4.2.1 Memory map Status and commandREAD instruction FUN237 4.2.2 Buffer memory access4. Register Configuration WRITE instruction FUN238 4. Register Configuration4.2.3 Parameter area 4. Register ConfigurationRSW1/2 information Status and command 0Status 1 4. Register ConfigurationSW2 information SW1 information4. Register Configuration CH1 receive error 16 and CH2 receive error Command 14. Register Configuration CH1 channel status 18 and CH2 channel status CH1 transmit error 17 and CH2 transmit error4. Register Configuration CH1 trailing code 24 and CH2 trailing code CH1 receive length 19 and CH2 receive length4. Register Configuration CH1 time-out check 25 and CH2 time-out check 4. Register Configuration4.2.4 Receiving and transmitting data area 4. Register Configuration5.7 Setting the time-out check time Section Operation Procedure5.5 Resetting the AS311 by software 5.6 Setting the trailing code 5.1 Transmission message format 5.2 Received message read sequence5. Operation Procedure 5.1 Transmission message format5.2 Received message read sequence 5.2.1 Flag control timing 5. Operation ProcedureOperation for receiving error Subroutine No 5.2.2 T3 sample program for message receiving5. Operation Procedure Main program Operation for normal received message5. Operation Procedure 5. Operation Procedure Explanation for this sample program5.3 Write sequence for message transmitting 5.3.1 Flag control timing 5. Operation ProcedureD0200 - D0263, and set R0110 to ON Operation for transmitting error 5.3.2 T3 sample program for message transmitting5. Operation Procedure Main program Set the transmission message into5. Operation Procedure 5. Operation Procedure 5.4 Checking the AS311 operation status 5. Operation Procedure5.5 Resetting the AS311 by software 5. Operation ProcedureH0003 5.6 Setting the trailing code5. Operation Procedure H80FE5.7 Setting the time-out check time 5. Operation Procedure6.1 LED indication 6.2 Buffer memory information 6.3 Trouble shooting Section RAS Information6. RAS Information 6.1 LED indication6.2.1 Module status 6.2 Buffer memory information6. RAS Information 6.2.2 Switch setting status 6. RAS Information6.2.3 Error information for data receiving 6. RAS Information6.2.4 Error information for data transmitting 6. RAS Information6.3 Trouble shooting 6. RAS Information58 ASCII Interface Module AS311 A.2 Specification of the WRITE instruction A.1 Specification of the READ instructionAppendix Function A.1 Specification of the READ instructionAppendix OperandAppendix Function A.2 Specification of the WRITE instructionAppendix OperandAppendix TOSHIBA CORPORATION Industrial Equipment Department