Manuals / Brands / TV and Video / DVR / Toshiba / TV and Video / DVR

Toshiba C-DR0101 7.8. Communication Settings

1 56

Download 56 pages, 743.85 Kb

NETWORK SETTING

IP ADDRESS

192. 168. 000. 001

SUBNET MASK

255. 255. 255. 000

DEFAULT GATEWAY

000. 000. 000. 000

COMMUNICATION SETTING

RS232C BAUD RATE [38400]

RS232C FLOW CTRL [OFF]

NETWORK SETTING

SWITCHER SYNC

[ OFF]

23

• Pressing the Menu key after the setting displays the confirmation

message in the lower part of the screen if the entered IP address is

different from the current IP address.

• Holding down the Select key for at least 1 second on the confirmation

message display screen displays the setting save screen.

• Press the Menu key if performing no setting. The display returns to

the normal communication setting screen.

NETWORK SETTING

IP ADDRESS

192. 168. 000. 001

SUBNET MASK

255. 255. 255. 000

DEFAULT GATEWAY

000. 000. 000. 000

SET THIS SETTING. OK?

YES : SELECT KEY 1SEC

NO : MENU KEY

NETWORK SETTING

SAVING SET DATA NOW.

PLEASE WAIT FOR A WHILE.

Setting Value Contents

Setting Item

RS232C BAUD

RATE

RS232C FLOW

CTRL

SWITCHER SYNC

(Switcher

Synchronization) *1

Sets the transmission rate.

Sets Flow Control RTS or CTS

ON : Controls the switcher through the RS-232C interface.

OFF :Controls no switcher

TIME SYNC : Only Time Synchronization can be controlled through the

RS-232C interface.

9600 / 19200 / 38400(bps)

ON / OFF

ON / OFF/ TIME SYNC

7.8.1. Network Settings

The Network Setting screen is displayed if Network Settings is selected on the communication setting screen.

Perform settings that are appropriate for the network.

• Move the cursor with the ( ) or ( ) key, and change setting values

with the (–) or (+) key.

* The underlined contents are factory-preset values.

7.8. Communication Settings

Set the transmission rate and whether or not to use flow control in RS-232C communications. Also set the IP

address, etc. to be used in the Ethernet network.

• Move the cursor with the ( ) or ( ) key, and change setting values

with the (–) or (+) key.

• Confirm the setting with the Menu key, and return to the previous

screen.

Note

*1Recording Pattern, Motion Detection Pattern, Camera/ VCR mode selection, and Time Synchronization

switcher functions can all be controlled by the Digital Video Recorder. However, when syncronizing the

switcher's clock from the Recorder, set the Recorder's clock Time Synchronization setting to "MASTER."

Time synhronization cannot be performed if set to "SLAVE."

Contents

Main 1CH DIGITAL VIDEO RECORDER (NTSC SYSTEM ) C-DR0100 C-DR0101 C-DR0105 INSTRUCTION MANUAL TABLE OF CONTENTS Page 14. CONNECTION EXAMPLES 15. RECORDING TIME TABLE WHEN YOU NEED HELP 16. EXTERNAL TERMINAL SPECIFICATIONS 17. RACK MOUNTING 18. IF YOU THINK THERE IS A FAILURE: (TROUBLESHOOTING) 19. SPECIFICATIONS WARNING CAUTION 3. FEATURES CAUTION 2. GENERAL DESCRIPTION 4. HANDLING PRECAUTIONS 12 3 4 5 6 7 8 91011 12 13 1415 16 5. NOMENCLATURE AND FUNCTIONS Page 21 22 23 24 25 26 27 28 18 19 17 20 2. Enter the setting screen. + 6. SETTING ITEM CHART AND SETTING PROCEDURES 6.1. Basic Setting Procedures The shaded item in the figure refers to the cursor position. 1. Enter the main menu screen. 6.2. Setting Item Chart 7.2. Playback Settings 7. INDIVIDUAL ITEM SETTINGS 7.1. Main Menu Screen 7.3. Clock Settings 7.4. Disk Settings 7.5. Recording Settings Page * The underlined contents are factory-preset values. with the () or (+) key. the table below. Timer Schedule Screen Settings with the () or (+) key. the table below. * The underlined contents are factory-preset values. Page 7.6. Screen Display Settings * The underlined contents are factory-preset values. the table below. with the () or (+) key. 7.7.1 Key Lock Release 7.7. Key Lock 7.8. Communication Settings 7.9. Log Display 7.10. System Maintenance Page 8. DIGITAL VIDEO RECORDER ACTIVATION AND TERMINATION 8.1. Recorder's Activation 8.2. When the Failure Screen Is Displayed: 8.3. Recorders Termination 9. OPERATION AFTER POWER FAILURE RESTORATION 9.1. When the Power Fails during Recording; 10. RECORDING 10.1. Type of Recording ** Page 10.5. Performing Internal Timer Recording 10.4. Performing General Recording 10.3. The Keys to Be Used in Recording 10.6. Performing Alarm Recording 11. PLAYBACK 11.1. Type of Playback 1 2 3 4 5 6 78 11.4. Performing Playback 11.5. Performing Various Playback Fanctions 11.3. The Keys to Be Used in Playback Page 11.6. About the Playback Start Position 12. SEARCH FUNCTIONS 12.2. Date/Time and Block Searches 12.1. The Keys to Be Used in Searching - 12.3. Time Shift Search 13. CONNECTIONS 13.1. Preparations for Connections 13.2. When Using the 24V AC or 12V DC or AC Mains Camera: 13.3. Connections to the Monitor TV 13.4. VIDEO OUT GND Video Input Video Output Video Input 1CH Digital Video Recorder 14. CONNECTION EXAMPLES 14.1. Connection to the 24V AC or 12V DC or AC Mains Camera. 1 9 GND 14.2. Connection to the Multi-switcher 14.2.1. Basic System (Combined with the C-MS91D Multi-switcher) Multi-switcher (C-MS91D) 1 Master 14.2.2. Expansion System (Combined with the C-MS91D Multi-switcher) 15.2. When using the C-DR0100 15. RECORDING TIME TABLE 15.3. When using the C-DR0101 15.1. Recording Picture Quality Setting 15.4. When using the C-DR0105 16. EXTERNAL TERMINAL SPECIFICATIONS 16.1. RS-232C Communication Specifications 16.1.4. RS-232C Communication Format (Controller Digital Recorder) Menu Setting Commands Note: Date/Time search is performed using setting data. Menu Setting Content Request Command Search Menu Execution Command Log Request Command Page Menu Setting Content Response Command Log Content Response Command Shown below are log information DATA section (13 bytes) formats. Search menu result command 16.2. About the Ethernet Terminal 17. RACK MOUNTING 18. IF YOU THINK THERE IS A FAILURE: (TROUBLESHOOTING) Symptom Remedy Possible Cause * 0dB = 1V 19. SPECIFICATIONS