Changing each setting in SS synchro. scan mode

(1. 2) Changing each setting in SS (synchro. scan) mode

Move up down						Set by pushing
By pushing						Set by pushing
By pushing						DATA UP, DOWN
MENU UP, DOWN						DATA UP, DOWN
MENU UP, DOWN

-- SHUTTER --
MODE	SS
SS	OFF
PART	OFF

<MODE = SS>

(a) Changing the shutter speed setting

•Shutter mode MANU, SS, E.TRG

•Synchro. scanning setting

OFF : 1H/796H↔795H/796H↔OFF↔2FRM↔512FRM

60fps, E.60fps : 1H/387H↔386H/387H↔OFF↔2FRM↔512FRM

90fps, E.90fps : 1H/258H↔257H/258H↔OFF↔2FRM↔512FRM

•Partial scanning switch OFF/60fps/90fps/E.60fps/E.90fps

1Set the "→" to SS by pushing [MENU UP], [MENU DOWN] buttons.

2Select the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.

(b) Partial scanning setting

1Set the "→" to PART by pushing [MENU UP], [MENU DOWN] buttons.

2Select either OFF/60fps/90fps/E.60fps/E.90fps by pushing [DATA UP], [DATA DOWN] buttons.

Note:

The slow shutter speed may increase the fixed pattern noise and/or the white pixels. This is a charac- teristic of CCD, and is not a symptom of malfunction.

Page 13

Image 13

Toshiba IK-TF7C Changing each setting in SS synchro. scan mode, Mode = SS, Changing the shutter speed setting

Contents

Following information is only for EU-member states For Customer Use Safety Precautions Disclaimer Avoid setting in humid, smoky, vaporized or dusty places Table of Contents Components Available selections Preset value Items Controlled by Using on Screen Display Names and Functions Connection Connector Pin AssignmentsStandard Connection White Balance OperationAutomatic White Balance Manual White Balance Outline Result displayed Meaning Gain Shutter speed mode is E.TRG modeShading Correction OFF Using the Menus Mode Setting by on Screen Display Partial scanning setting Changing each setting in Manu modeMenus Shutter Electronic shutter Mode = SS Changing each setting in SS synchro. scan modeChanging the shutter speed setting Changing each setting in 1P SNR mode Changing each setting in E.TRG modeChanging the polarity of inputting trigger pulse setting Changing 1P SNR exposure time setting Mode = E.TRG E.TRG = 1P SR Changing each setting in 1P SR modeChanging 1P SR exposure time setting Mode = E.TRG E.TRG = PW SNR Changing each setting in PW SNR mode Mode = E.TRG E.TRG = PW SR Changing each setting in PW SR mode Mode = E.TRG E.TRG = RR Changing each setting in RR modeChanging each setting in Gain Changing the gain in Manu mode WHT BAL White balance Changing the manual shading correction setting Changing the shading correction modeChanging master pedestal Changing R pedestal Sync Adjusting horizontal phaseOption Data UP, Down Menu UP, Down External sync signal polarity Setting to factory setting statusShutter mode HD input VD input External Sync Using the unit with external sync signal Setting by the frameSetting by 1H Horizontal phase adjustment 1 Pulse Trigger SYNC-NON Reset Picture Output Timing 1P SNR 1 Pulse Trigger Sync Non ResetEXT Trig External trigger Fval Lval Dval Ger, there will be an effect on the video 1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Trigger Sync Reset PW SNR Pulse width trigger SYNC-NON Reset Trigger*1 About 1 ∝s 1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESET Input Timing Chart Example RR Reset restartLong Term Exposure Partial Scanning When Partial Scanning Mode is onPartial Scanning OFF All pixels scanning Partial Scanning on Input Output Signal Specificatoins Horizontal Output Waveform Timing Chart CCD Output Waveform Timing ChartVertical Output Waveform Timing Chart RGB, 3CCD Specifications Before Making a Service Call External Appearance DiagramSymptom Items to be checked Step-by-step Procedures How to Obtain Warranty Service Limited One 1 Year Warranty of Labor and PartsImaging Systems Division

Toshiba IK-TF7C instruction manual Changing each setting in SS synchro. scan mode, Mode = SS

Models: IK-TF7C

(1. 2) Changing each setting in SS (synchro. scan) mode

<MODE = SS>

(a) Changing the shutter speed setting

(b) Partial scanning setting