Input Output Signal Specificatoins | Toshiba IK-TF7C specification

8. INPUT OUTPUT SIGNAL SPECIFICATOINS

( 1 ) HD Input Specifications					( 2 ) VD Input Specifications

5H to 21H

2.0 ∝s to 5.0 ∝s

( 3 ) Trigger Pulse Specifications

More than 2 ∝s			(Positive polarity mode)



More than 2 ∝s			(Negative polarity mode)

( 6 ) External HD/VD Input Phase Specifications

External HD rising edge

100

External HD

100

Unit : Clock

1 clk=33.9nsec

Center

The phase relationship of the external HD and VD should correspond to the center phase (i.e., the external HD falling edge) as illustrated in the above diagram.

External VD falling edge:

Please input within about 100 clock cycles of the standard center phase.

Note that V sync of the video is output with a delay of about 1H from the external VD at the time of reset-restart and the external trigger mode.

In the normal mode:

Continuously with the HD period of 43.05 ∝s and VD period of 34.27 ms (partial scanning 60fps: 16.67 ms, partial

scanning 90fps: 11.11 ms ).

Phase timing is as illustrated in the above diagram (with only the falling edge applicable).

In the reset-restart/external trigger mode:

Continuously with the HD period of 43.05 ∝s. VD (reset) is at an arbitrary timing with the phase of HD being within the standard of the above diagram.

32

Image 32

Toshiba IK-TF7C instruction manual Input Output Signal Specificatoins

Contents

For Customer Use Following information is only for EU-member states Safety Precautions Avoid setting in humid, smoky, vaporized or dusty places Disclaimer Table of Contents Components Items Controlled by Using on Screen Display Available selections Preset value Names and Functions Standard Connection Connector Pin AssignmentsConnection Operation White BalanceAutomatic White Balance Manual White Balance Outline Result displayed Meaning Shutter speed mode is E.TRG mode GainShading Correction OFF Mode Setting by on Screen Display Using the Menus Changing each setting in Manu mode Partial scanning settingMenus Shutter Electronic shutter Changing the shutter speed setting Changing each setting in SS synchro. scan modeMode = SS Changing each setting in E.TRG mode Changing each setting in 1P SNR modeChanging the polarity of inputting trigger pulse setting Changing 1P SNR exposure time setting Changing 1P SR exposure time setting Changing each setting in 1P SR modeMode = E.TRG E.TRG = 1P SR Changing each setting in PW SNR mode Mode = E.TRG E.TRG = PW SNR Changing each setting in PW SR mode Mode = E.TRG E.TRG = PW SR Changing each setting in RR mode Mode = E.TRG E.TRG = RRChanging each setting in Gain Changing the gain in Manu mode WHT BAL White balance Changing the shading correction mode Changing the manual shading correction settingChanging master pedestal Changing R pedestal Adjusting horizontal phase SyncOption Data UP, Down Menu UP, Down Setting to factory setting status External sync signal polarityShutter mode HD input VD input External Sync Setting by the frame Using the unit with external sync signalSetting by 1H Horizontal phase adjustment 1P SNR 1 Pulse Trigger Sync Non Reset 1 Pulse Trigger SYNC-NON Reset Picture Output TimingEXT Trig External trigger Fval Lval Dval Ger, there will be an effect on the video 1P SR 1 Pulse Trigger Sync Reset 1 Pulse Trigger SYNC-RESET Picture Output Timing PW SNR Pulse width trigger SYNC-NON Reset Trigger*1 About 1 ∝s PW SR Pulse width trigger SYNC-RESET 1 Pulse Width Trigger SYNC-RESET Picture Output Timing Long Term Exposure RR Reset restartInput Timing Chart Example When Partial Scanning Mode is on Partial ScanningPartial Scanning OFF All pixels scanning Partial Scanning on Input Output Signal Specificatoins Vertical Output Waveform Timing Chart CCD Output Waveform Timing ChartHorizontal Output Waveform Timing Chart Specifications RGB, 3CCD Symptom Items to be checked External Appearance DiagramBefore Making a Service Call Imaging Systems Division Limited One 1 Year Warranty of Labor and PartsStep-by-step Procedures How to Obtain Warranty Service