End | Toshiba S20LP specification

6 F 3 B 0 3 5 6

/* Register readout */

R0093

[08450 MOV D0920]

[00000 MOV D0921]

/* Designates the module and sets the CMD number. */

[RW092 MOV D0922]

/* Sets the transfer register data length. */

[RW097 MOV D0923]

[RW098 MOV D0924]

/* Sets the transmission source register type, leading address. */

[RW095 MOV D0925]

[RW096 MOV D0926]

/* Sets the transfer destination register type, leading address. */

[00100 MOV D0927]

/* Sets the response time limit (10 seconds). */

[D0920 SEND D0928]

[SET R0094]

[RST R0093]

/* Sets the request, and starts post-completion comparison. */

/* Comparison check */

R0094

[00001 MOV D0940]

[00001 MOV D0941]

[00980 MOV D0942]

[00001 MOV D0943]

[00981 MOV D0944]

[RW094ŸRW093 DMOV D0948ŸD0947]

[RW098ŸRW097 DMOV D0950ŸD0949]

R0095

[D0947 XFER D0940

D0941]

R0096

[D0949 XFER D0940

D0943]

(

)

R0096

[D0980 = D0981]

[ +1 RW190]

R0910

[D0980 <> D0981]

[ +1 RW191]

[SET R0099]

[RST R0094]

R0095

[ +1 D0945]

[ +1 D0948]

[ +1 D0950]

(

)

R0097

[RW092 = D0945]

[00000 MOV D0945]

[ +1 D0946]

(

)

R0097

[RW090 > D0946]

[SET R0091]

[RST R0094]

[END]

[RW090 = D0946]

[00000 MOV D0946]

⎯ 61 ⎯

Image 62

Toshiba S20LP instruction manual End

Contents

T2N/T3H stations Important Information Preface Contents System configuration Introduction to S20LP T2N include of S20LP Port Station hardware∙ Overview SN325 SN325 For SN325 ∙ Status LEDsS20LP port for T2N PU245N ∙ Reset switch only SN325 ∙ Station number setting switches∙ Transmission cable connectors ∙ Loader port LS overview Menu ⎯ 10 ⎯ S20LP-station specifications SpecificationsS20LP system specifications Scan transmission overview Setting the data send block by S-LS Allocation and network assignment by T-PDS Settings on T-PDS Setting for data linkageStation number setting Link PDS screen example Block Send Receive ⎯ 18 ⎯ Global ⎯ 20 ⎯ Settings on S-LS ⎯ 22 ⎯ ⎯ 23 ⎯ ⎯ 24 ⎯ ∙ Scan Transmission ∙ Scan Access∙ Start with Standby mode ∙ Message Transmission ∙ Target Scan Time Data linkage example ∙ Settings on T-PDS Setting on S-LS LS setting screen 2 for STN #2 Cable connections ∙ Station down RAS functionBehavior in trouble ∙ Transmission cable breakage During operation Self-diagnostic functionAt initialization at power on T2N LED indicationSN325 RAS information monitored in T2N/T3H Station status Online map Standby map Loop map Only T2N RAS information monitored on S-LS Number 1-64 on the screen shows the Station number Self Station Station No.01 Offline Select the Station Number Click the Status Display Possible error message are as follows Station down information Instruction format Instruction SpecificationExpanded data transfer instruction Function Parameter and construction Transfer parameter table Sample program ∙ Operation Remarks Computer link protocol Message transmissionMessage transmission PC link protocol ∙ Send Transfer parameters a CMD Status B TermSTS Status Meaning Detailed Information Send completion status PC link protocol transmission Data write Transfer parameters RID Status See 7.3 5 for details on bits C, D, E, and F Important items XW/YW PC link protocol transmission Data read ⎯ 57 ⎯ SW067 Write enabled PC link protocol transmission program Remarks Length END Appendix Scan cycle ⎯ 63 ⎯ PDS remote programming PDS Setup options screen