Displaying Information, Press Call | Toshiba TLP780E instruction

Displaying Information

CONTENTS

41

Remote control

INPUTON/STANDBY

	LASER
KEYSTONE	AUTO	SET
KEYSTONE		SET

L-CLICKR-CLICK

VOLUME/ADJUST

MENU ENTER EXIT

Information on the input signal source, etc., can be displayed.

CALL					Press CALL.
CALL
					The information described below is displayed.
					The information display turns off when the CALL button is
					pressed again.
				Status display


Input						- current input source
H-resolution						- the horizontal resolution of the input signal (at RGB input)
V-resolution						- the vertical resolution of the input signal (at RGB input)
H-frequency						- the horizontal frequency of the input signal (at RGB input)
V-frequency						- the vertical frequency of the input signal (at RGB input)
Sync						- the polarity of the sync signal (at RGB input)
Video mode						- the color mode of the video signal (at Video, S-Video input)
Signal format- the formatting of the Y/PB/PR signal (at Y/PB/PR input)
Lamp time						- the elapsed usage time of the lamp
Version						- the version of the firmware
Shutter						- the shutter speed of the document imaging camera (at
						document imaging camera input)

Operations

CALL

PIP FREEZE

RESIZE

CALL MUTE

Notes

•The information displayed is not refreshed even if it changes. To refresh the information, turn off the information display, then turn it back on.

•The information display turns off if any other operation is performed.

•The “Lamp time” shows an approximate time for lamp replacement. (It should not be used as a lamp warranty time counter.) If the time indicated here nears 1000, contact your store of purchase about obtaining a replacement lamp (TLPL78, sold separately).

•The “Lamp time” can be reset when the lamp is replaced.

•The “Version” is the version of the control program used in the projector and is used for servicing, etc.

Image 41

Toshiba TLP780E owner manual Displaying Information, Press Call

Contents

TLP780E TLP781E Safety Precautions Moisture Condensation Save Original Packing MaterialsAvoid Volatile Liquid Ventilation Power SourcesSource of Light Important Safety Instructions Object and Liquid Entry AccessoriesDo not place the product vertically Stack Inhibited Replacement Parts Damage Requiring ServiceSafety Check Servicing Do not move the projector while the arm is still erect Do not carry by the camera armDo not look into the arm light while it is lit Strong light may cause damage to your eyes or sight Power supply cord selection Contents Refer to Names of each part on the main unitExplanation here is only for the model without the document Menu button Input button Names of each part on the main unitTop side Right side Names of each part on the remote control Loading batteries Install the batteriesOpen the cover Attach the cover Rear side Remote control operationFront side Viewer Floor-mounted projector placement Side view Determine the screen size projected on the screenTop view Light Orange Power cord Supplied Connect the power cordTake off the lens cover Insert the other end into a wall outlet Foot adjuster Foot adjuster release button Projector placement angle adjustmentLift up Lower Turn clockwise to lift up Turn counterclockwise to lower Viewer Translucent screen Ceiling-mounted projector placement Connecting a computer Computer in 1 connector Connecting a computer Computer in 2 connector Connecting video equipment Connectionsand Computer Projector operation control by a computer How to use the output connector Projection on the screen Remote controlPress ON/STANDBY Lamp lights and the start up display appears Press Enter to confirm Turn on the connected equipment and put it in playback modeControl panel Main unit side Language Press Input and hold for two seconds Select the input source by pressing Input repeatedlyPress Enter Input source selection menu appears Focusing ring Adjust the picture size by turningStill picture is recommended for focusing Zooming lever About the LCD Panel Press VOL/ADJ +/- to adjust volume Press ON/STANDBY after using the projector Turning the power offPress ON/STANDBY again Control panel Input full screen video signals from the input Adjusting the picture automaticallySource computer and project the image Press Auto SET Confirm the keystone distortion Correcting the keystone distortionPress Keystone After confirming that V-keystone is selected on the menu Keystone adjustment finishes Cutting off the picture and sound temporarily Icon appears in the mute modePress Mute Sound and picture are cut off temporarily Freezing the picture Icon appears in the freeze modePress Freeze Picture freezes Press Resize Icon appears in the resize modeEnlarging the picture size Sub-picture is displayed Displaying PIP Sub-picturesPress PIP Press Call Displaying Information Operating a computer by the remote control Press Menu Operating the menu screenPress Menu once again Select the item with the selection Buttons Select the item with selection buttons Adjust with VOL/ADJ +Enter Press Enter Press Enter Shutter Guide Menu adjustments and settings Full Menu adjustments and settings Picture Full Menu adjustments Position Full Menu adjustments Color Full Menu adjustments and settings Audio Settings Adjustments Full Menu adjustments and settings Display Full Menu settings Default setting Reset all Full Menu settings Reset PIP menu setting ImagingDocument camera Preparation of the document imaging camera Camera head over them Press ARM LightSet a document to be projected Move the camera head to adjust the size of the picture Press Camera to select the camera input mode Press Camera Gain +/- to improve view of a When finished, turn off the light and close itCamera subject which is too dark or vivid Put back the arm Overlaying projection Locking the white balance Balance Press W.BALANCE to turn the Lock indicatorProject a white paper and enlarge it to fill Screen With the document camera operating, fully Correcting illuminated defectsCover the camera lens with a piece of black Paper or cloth Main unit side Trouble indications Unplug the power cord Take off the air filter cover Air filter cleaningClean the air filter Detach the air filter Air filter Air filter cover Assemble the air filterMount the air filter cover Cleaning the lens Lens and main unit cleaningCleaning the main unit Replacing the intake, exhaust fans and air filter Unplug the power cord Wait until the lamp gets cool enough Lamp replacementTake off the lamp cover on the bottom panel Pull out the lamp Load a new lamp Reset the lamp timerAttach the lamp cover Slide the cover into place and tighten the two screws Symptom Cause Correction Before calling service personal Before calling service personal Do not connect anything Mini D-sub 15pin Connector Applicable computer signal Applicable signalSignal Timing Horizontal Signal Timing Vertical Timing chart Compatible components video signal Y/PB/PR Applicable signalCompatible Video and S-Video signal Command list Controlling the projector by using RS-232CSignal assignment of RS-232C Interface format Controlling the projector by using RS-232C VCL MO0 MS0 PIP Main unit SpecificationsLiquid crystal display Projection lens Accessories SpecificationsReplacement lamp Sold separately