Trouble indications
If there is some problem inside the projector, the indicators light up or blink.
CONTENTS | 62 |
LAMP | TEMP | FAN | The power does not come on. |
ON |
| → Malfunction of the unit. | |
(Off) |
|
| |
|
| • Unplug the power cord and call the dealer. | |
|
|
|
Or 
(Lit in red)
LAMP
ON
(Lit in red)
(Lit in red)
TEMP | FAN |
|
The lamp turns off or does not light up.
→The projector will return to the standby mode in about 2 minutes.
If the projector does not operate normally when the power is switched on again, the lamp is at the end of its life duration or the unit has a fault.
•Lamp's life duration is over, replace the lamp with a new one. 66
•Unplug the power cord and call the dealer.
Indicators
|
| ON / STANDBY |
|
|
| P | T | EMP |
|
ON | LAM |
| F | |
|
|
| AN |
ON | LAMP |
|
(Lit in red)
TEMP | FAN |
|
(Lit in red) 
(Lit in green)
Or 
(Lit in orange)
Or 
(Lit in green)
Or 
(off)
The power turns off or does not come on.
→The inside is too hot, or the projector has been working in an area of high temperature.
•Place the projector correctly so the intake and exhaust fan's holes are not covered.
•Turn the projector off, and leave it for a while, and turn it on again.
•Clean the air filter. 63
*The 
icon appears before the power turned off.
*The projector returns to the standby mode after the fault display has been shown for about 2 minutes.
|
|
|
|
| R |
| EXI |
|
|
|
|
| TE |
|
| ||
|
|
|
| EN |
|
| T |
|
|
|
|
| U |
|
| A |
|
|
|
|
|
|
| UT |
| |
|
|
|
| N |
|
| O | S |
|
|
|
| E |
|
|
| |
|
|
|
| M |
|
|
| E |
|
|
|
|
|
|
| T | |
|
|
|
|
|
|
|
| K |
|
|
|
| T |
|
|
| E |
|
|
| U |
|
|
| Y | |
|
| P |
|
|
| S | ||
| N |
|
|
|
| T | ||
I |
|
|
|
|
| O | ||
|
|
|
|
|
| N | ||
|
|
|
|
| VOL / ADJ |
| E | |
|
|
|
|
|
|
|
| |
LAMP
ON
(Lit in red)
TEMP | FAN |
|
(Lit or flashing in red)
Or
(Lit or flashing in orange)
The power turns off or does not come on.
→Trouble with the cooling fan.
• Unplug the power cord and call the dealer.
*The 
icon appears before the power turned off.
*The projector returns to the standby mode after the fault display has been shown for about 2 minutes.
Control panel
(Main unit side)
LAMP | |
ON |
|
(Lit in red) | (Flashing |
| in orange) |
Notes
TEMP | FAN | The power turns off or does not come on. |
| → The lamp cover is not properly attached. | |
|
| |
|
| • Unplug the power cord and reattach the lamp cover. 67 |
* The 
icon appears before the power turned off.
*The projector returns to the standby mode after the fault display has been shown for about 2 minutes.
Maintenance
•If abnormality occurs while operating, unplug the power cord.
•When reinserting the power cord before the lamp has cooled, please wait until the lamp has cooled sufficiently before use. When the lamp is at a high temperature, it may not light and the life duration will be shortened.
