Transcend Information TS8GCF600, TS16GCF600 dimensions PC Card Memory Mode PC Card I/O Mode

TS8G~16GCF600 600X CompactFlash Card

Pin

Num

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

PC Card Memory Mode				PC Card I/O Mode
Signal Name	Pin	In, Out	Pin	Signal Name	Pin	In, Out	Pin
	Type	Type	Num		Type	Type	Num
-HIOE				-HIOE
HSTROBE10	I	I3U	34	HSTROBE10	I	I3U	34
HDMARDY11				-HDMARDY11
-IOWR	I	I3U	35	-IOWR	I	I3U	35
STOP10,11				STOP10,11
-WE	I	I3U	36	-WE	I	I3U	36
READY	O	OT1	37	-IREQ	O	OT1	37
VCC		Power	38	VCC		Power	38
-CSEL5				-CSEL5
	I	I2Z	39		I	I2Z	39
-VS2	O	OPEN	40	-VS2	O	OPEN	40
RESET	I	I2Z	41	RESET	I	I2Z	41
-WAIT				-WAIT
-DDMARDY10	O	OT1	42	-DDMARDY10	O	OT1	42
DSTROBE11				DSTROBE11
-INPACK	O	OT1	43	-INPACK	O	OT1	43
-DMARQ12				-DMARQ12
-REG	I	I3U	44	-REG	I	I3U	44
-DMACK 12				DMACK 12
BVD2	O	OT1	45	-SPKR	O	OT1	45
BVD1	O	OT1	46	-STSCHG	O	OT1	46
D081	I/O	I1Z,	47	D081	I/O	I1Z,	47
		OZ3				OZ3
D091	I/O	I1Z,	48	D091	I/O	I1Z,	48
		OZ3				OZ3
D101	I/O	I1Z,	49	D101	I/O	I1Z,	49
		OZ3				OZ3
GND		Ground	50	GND		Ground	50

True IDE Mode4

Signal Name	Pin
	Type
-HIOE7
HSTROBE8	I
-HDMARDY9
-IOWR7	I
STOP8,9
-WE3	I
INTRQ	O
VCC
-CSEL	I
-VS2	O
-RESET	I
IORDY7
-DDMARDY8	O
DSTROBE9
DMARQ	O
-DMACK 6	I
-DASP	I/O
-PDIAG	I/O
D081	I/O
D091	I/O
D101	I/O
GND

In, Out

Type

I3Z

I3Z

I3U

OZ1

Power

I2U

OPEN

I2Z

ON1

OT113

OZ1

I3U

I1U, ON1 I1U, ON1 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 Ground

Note: 1) These signals are required only for 16 bit accesses and not required when installed in 8 bit systems. Devices should allow for 3-state

signals not to consume current.

2)The signal should be grounded by the host.

3)The signal should be tied to VCC by the host.

4)The mode is required for CompactFlash Storage Cards.

5)The -CSEL signal is ignored by the card in PC Card modes. However, because it is not pulled upon the card in these modes, it should not be left floating by the host in PC Card modes. In these modes, the pin should be connected by the host to PC Card A25 or grounded by the host.

6)If DMA operations are not used, the signal should be held high or tied to VCC by the host. For proper operation in older hosts: while DMA operations are not active, the card shall ignore this signal,including a floating condition

7)Signal usage in True IDE Mode except when Ultra DMA mode protocol is active.

8)Signal usage in True IDE Mode when Ultra DMA mode protocol DMA Write is active.

9)Signal usage in True IDE Mode when Ultra DMA mode protocol DMA Read is active.

10)Signal usage in PC Card I/O and Memory Mode when Ultra DMA mode protocol DMA Write is active.

11)Signal usage in PC Card I/O and Memory Mode when Ultra DMA mode protocol DMA Read is active.

12)Signal usage in PC Card I/O and Memory Mode when Ultra DMA protocol is active.

Transcend Information Inc. 6

V1.0