Transcend Information TS8GCF600, TS16GCF600 guide

TS8G~16GCF600		600X CompactFlash Card

Common Memory Write Timing Specification

	Cycle Time Mode:		250 ns			120 ns		100 ns		80 ns

		IEEE	Min		Max	Min	Max	Min	Max	Min	Ma
Item	Symbol	IEEE	Min		Max	Min	Max	Min	Max	Min	x
Item	Symbol	Symbol	ns.		ns.	ns.	ns.	ns.	ns.	ns.	x
		Symbol	ns.		ns.	ns.	ns.	ns.	ns.	ns.	ns.
											ns.
Data Setup before HWE	tsu (HD-HWEH)	tDVWH	80			50		40		30

Data Hold following HWE	th(HD)	tWMDX	30			15		10		10

HWE Pulse Width	tw(HWE)	tWLWH	150			70		60		55

Address Setup Time	tsu(HA)	tAVWL	30			15		10		10

CEx Setup before HWE	tsu(CEx)	tELWL	5			5		5		5

Write Recovery Time	trec(HWE)	tWMAX	30			15		15		15

Address Hold Time	th(HA)	tGHAX	20			15		15		15

CEx Hold following HWE	th(CEx)	tGHEH	20			15		15		10

Wait Delay Falling from HWE	tv (IORDY-HWE)	tWLWTV			35		35		35		na1

WE High from Wait Release	tv(IORDY)	tWTHWH	0			0		0		na1

Wait Width Time2	tw (IORDY)	tWTLWTH			350		350		350		na1

Notes: 1) –WAIT is not supported in this mode.

2)The maximum load on -WAIT is 1 LSTTL with 50 pF (40pF below 120nsec Cycle Time) total load. All times are in nanoseconds. Din signifies data provided by the system to the CompactFlash Storage Card. The -WAIT signal may be ignored if the -HWE cycle to cycle time is greater than the Wait Width time. The Max Wait Width time can be determined from the Card Information Structure. The Wait Width time meets the PCMCIA PC Card specification of 12µs but is intentionally less in this specification.

Transcend Information Inc.

24

V1.0

Image 24

Transcend Information TS8GCF600 Common Memory Write Timing Specification, Cycle Time Mode 250 ns 120 ns 100 ns 80 ns

Contents

Placement Features Power Consumption DimensionsDescription Transcend Block Diagram TS8G~16GCF600 PC Card Memory Mode PC Card I/O Mode True IDE Mode4 Pin Assignments and Pin Type PC Card Memory Mode PC Card I/O Mode Input Characteristics Input Leakage CurrentOutput Drive Type Output Drive Characteristics Output Drive CharacteristicsSymbol Conditions Signal Description Signal Name Dir Pin Description600X CompactFlash Card Csel GND Hdmardy Hstrobe Signal Name DirPin Description Reset REGDmack Iordy DdmardyDstrobe Electrical Specification Input Power Input Characteristics for Udma mode SymbolOutput Drive Characteristics for Udma mode Parameter Symbol Signal Interface Signal Card Host Pull-up pin 45 BVD2 to avoid sensing their batteries as Low 150 a high state per socket Ultra DMA Electrical Requirements Series termination required for Ultra DMA operationTable Typical Series Termination for Ultra DMA Ultra DMA Mode Cabling Requirement Attribute Memory Read Timing Specification Speed Version 300 ns Symbol Ieee Symbol Min ns Max ns Table Configuration Register Attribute Memory Write Timing Speed Version 250 ns Symbol Min ns Max ns Common Memory Read Timing Specification Cycle Time Mode 250 ns 120 ns 100 ns 80 ns SymbolMin Max Symbol Ieee Common Memory Write Timing Specification Cycle Time Mode 250 ns 120 ns 100 ns 80 ns Input Read Timing Specification Data Delay after Hioe TdHIOE TlGLQVData Delay from Wait Rising2 TdIORDY TWTHQV Wait Width Time2 TwIORDY TWTLWTH Output Write Timing Specification Cycle Time Mode 255 ns 120 ns 100 ns 80 ns True IDE PIO Mode Read/Write Timing Specification ModeT6Z TS8G~16GCF600 True IDE Multiword DMA Mode Read/Write Timing Specification TS8G~16GCF600 True IDE Ultra DMA Mode Read/Write Timing Specification PC Card MEM PC Card IO ModeMode Udma True IDE Mode Udma TS8G~16GCF600 Name Name Comment Name Mode Mode4 Min Max14.7 72.9 50.9 Name Min Max Card Configuration Multiple Function CompactFlash Storage CardsREG Selected Space Dmardy Strobe Dmarq Dmack Stop HioeDMA Inpack REG Hiow Wait Hioe CMD Attribute Memory Function Table Attribute Memory FunctionDMA CMD REG Configuration Option Register Base + 00h in Attribute Memory TS8G~16GCF600 Pin Replacement Register Base + 04h in Attribute Memory Socket and Copy Register Base + 06h in Attribute Memory Table Pcmcia Mode I/O Function Transfer FunctionDMA CMD REG -CE2 Table PC Card I/O Mode Udma Function Dmarq Dmack Stop Hioe Wait DMA A10Inpack REG Hiow Wait Hioe CMD A00 Common Memory Transfer Function Table Common Memory FunctionDMA REG CE2 CE1 D15-D8 True IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol Primary and Secondary Address Configurations Table Primary and Secondary I/O Decoding Contiguous I/O Mapped Addressing Table Contiguous I/O Decoding True IDE Mode Addressing Memory Mapped Addressing CF-ATA Registers Data Register Address 1F0h170hOffset 0,8,9 Feature Register Address 1F1h171h Offset 1, 0Dh Write Only Sector Count Register Address 1F2h172h OffsetSector Number LBA 7-0 Register Address 1F3h173h Offset Cylinder Low LBA 15-8 Register Address 1F4h174h Offset TS8G~16GCF600 Device Control Register Address 3F6h376h Offset Eh Card Drive Address Register Address 3F7h377h Offset Fh CF-ATA Command Set Command Code Definitions Check Power Mode 98h or E5h Execute Drive Diagnostic 90hBit Command Cyl High Cyl Low Sec Num Sec Cnt Feature Transcend Information Inc Erase Sectors C0hFlush Cache E7h Format Track 50h Drive Cyl High Cyl Low Sec Num Sec Cnt Feature Word Default Total Data Field Type InformationIdentify Device Ech Bytes PIO data transfer cycle timing mode Command sets supportedXXXXh Command sets enabled Ultra DMA Mode Supported and Selected Word 0 General Configuration CF Advanced True IDE Timing Mode Capability and SettingCF Advanced PC Card I/O and Memory Timing Mode Capability Key management schemes supported Word 1 Default Number of Cylinders Word 3 Default Number of HeadsWord 6 Default Number of Sectors per Track Word 49 Capabilities Bit 13 Standby Timer Multiple Sector Setting Total Sectors Addressable in LBA ModeCurrent Number of Cylinders, Heads, Sectors/Track Current Capacity Words 82-84 Features/command sets supported Recommended Multiword DMA transfer cycle timeWord 68 Minimum PIO transfer cycle time with Iordy Words 85-87 Features/command sets enabled Word 88 Ultra DMA Modes Supported and Selected Word 91 Advanced power management level value Word 89 Time required for Security erase unit completionWord 128 Security Status Bit 8 Security Level Word 160 Power Requirement Description Value Maximum PIO mode timing selectedValue Maximum Multiword DMA timing mode supported Additional Requirements for CF Advanced Timing Modes Value Current PIO timing mode selected Value Maximum Pcmcia IO timing mode SupportedValue Maximum Memory timing mode Supported Current Multiword DMA timing mode selected Value Maximum PC Card I/O Udma timing mode Supported Value Maximum PC Card Memory Udma timing mode SupportedValue PC Card Memory or I/O Udma timing mode Selected Idle 97h or E3h Idle Immediate 95h or E1hInitialize Drive Parameters 91h Drive Cyl High Cyl Low Sec Num Sec Cnt NOP 00h Read Buffer E4hRead DMA C8h Read Long Sector 22h or 23h TS8G~16GCF600 Seek 7Xh Set Features EFh Request Sense 03h Feature Supported TS8G~16GCF600 Standby Immediate 94h or E0h Translate Sector 87h Translate Sector Information Wear Level F5h Write Buffer E8h Write DMA CAh TS8G~16GCF600 TS8G~16GCF600 Error Posting BBK UNC Idnf Abrt Amnf Drdy DWF DSC Corr ERRNOP S. Table Capacity Ordering Information Transcend Product Capacity CompactFlash Card