Ieee, Min Max Symbol | Transcend Information TS16GCF600, TS8GCF600

TS8G~16GCF600		600X CompactFlash Card

Common Memory Read Timing Specification

		Cycle Time Mode:		250 ns		120 ns		100 ns		80 ns

	Item	Symbol	IEEE	Min	Max	Min	Max	Min	Max	Min	Max
	Item	Symbol	Symbol	ns.	ns.	ns.	ns.	ns.	ns.	ns.	ns.
			Symbol	ns.	ns.	ns.	ns.	ns.	ns.	ns.	ns.

	Output Enable Access Time	ta(HOE)	tGLQV		125		60		50		45

	Output Disable Time from HOE	tdis(HOE)	tGHQZ		100		60		50		45

	Address Setup Time	tsu(HA)	tAVGL	30		15		10		10

	Address Hold Time	th(HA)	tGHAX	20		15		15		10

	CEx Setup before HOE	tsu(CEx)	tELGL	5		5		5		5

	CEx Hold following HOE	th(CEx)	tGHEH	20		15		15		10

	Wait Delay Falling from HOE	tv(IORDY-HOE)	tGLWTV		35		35		35		na1

	Data Setup for Wait Release	tv(IORDY)	tQVWTH		0		0		0		na1

	Wait Width Time2	tw(IORDY)	tWTLWTH		350		350		350		na1

Notes:1) –WAIT is not supported in this mode.

2)The maximum load on -WAIT is 1 LSTTL with 50 pF (40pF below 120nsec Cycle Time) total load. All times are in nanoseconds. Dout signifies data provided by the CompactFlash Storage Card to the system. The -WAIT signal may be ignored if the -OE cycle to cycle time is greater than the Wait Width time. The Max Wait Width time can be determined from the Card Information Structure. The Wait Width time meets the PCMCIA PC Card specification of 12µs but is intentionally less in this specification.

Transcend Information Inc.

23

V1.0

Image 23

Transcend Information TS16GCF600, TS8GCF600 dimensions Common Memory Read Timing Specification, Ieee, Min Max Symbol

Contents

Description Placement FeaturesPower Consumption Dimensions Transcend Block Diagram TS8G~16GCF600 Pin Assignments and Pin Type PC Card Memory Mode PC Card I/O Mode True IDE Mode4 PC Card Memory Mode PC Card I/O Mode Output Drive Type Input CharacteristicsInput Leakage Current Symbol Conditions Output Drive CharacteristicsOutput Drive Characteristics 600X CompactFlash Card Signal DescriptionSignal Name Dir Pin Description GND Csel Hstrobe Hdmardy Pin Description Signal NameDir Dmack ResetREG Dstrobe IordyDdmardy Electrical Specification Parameter Symbol Input Power Input Characteristics for Udma modeSymbol Output Drive Characteristics for Udma mode Signal Card Host Signal Interface 150 a high state per socket Pull-up pin 45 BVD2 to avoid sensing their batteries as Low Table Typical Series Termination for Ultra DMA Ultra DMA Electrical RequirementsSeries termination required for Ultra DMA operation Ultra DMA Mode Cabling Requirement Speed Version 300 ns Symbol Ieee Symbol Min ns Max ns Attribute Memory Read Timing Specification Speed Version 250 ns Symbol Min ns Max ns Table Configuration Register Attribute Memory Write Timing Ieee Common Memory Read Timing SpecificationCycle Time Mode 250 ns 120 ns 100 ns 80 ns Symbol Min Max Symbol Cycle Time Mode 250 ns 120 ns 100 ns 80 ns Common Memory Write Timing Specification Wait Width Time2 TwIORDY TWTLWTH Input Read Timing SpecificationData Delay after Hioe TdHIOE TlGLQV Data Delay from Wait Rising2 TdIORDY TWTHQV Cycle Time Mode 255 ns 120 ns 100 ns 80 ns Output Write Timing Specification T6Z True IDE PIO Mode Read/Write Timing SpecificationMode TS8G~16GCF600 True IDE Multiword DMA Mode Read/Write Timing Specification TS8G~16GCF600 True IDE Mode Udma True IDE Ultra DMA Mode Read/Write Timing SpecificationPC Card MEM PC Card IO Mode Mode Udma TS8G~16GCF600 Name Name Comment 72.9 50.9 Name Mode Mode4Min Max 14.7 Min Max Name Selected Space Card ConfigurationMultiple Function CompactFlash Storage Cards REG Inpack REG Hiow Wait Hioe CMD Dmardy StrobeDmarq Dmack Stop Hioe DMA DMA CMD REG Attribute Memory FunctionTable Attribute Memory Function Configuration Option Register Base + 00h in Attribute Memory TS8G~16GCF600 Pin Replacement Register Base + 04h in Attribute Memory Socket and Copy Register Base + 06h in Attribute Memory REG -CE2 Table Pcmcia Mode I/O FunctionTransfer Function DMA CMD Inpack REG Hiow Wait Hioe CMD A00 Table PC Card I/O Mode Udma FunctionDmarq Dmack Stop Hioe Wait DMA A10 CE2 CE1 D15-D8 Common Memory Transfer FunctionTable Common Memory Function DMA REG True IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol Table Primary and Secondary I/O Decoding Primary and Secondary Address Configurations Table Contiguous I/O Decoding Contiguous I/O Mapped Addressing Memory Mapped Addressing True IDE Mode Addressing Data Register Address 1F0h170hOffset 0,8,9 CF-ATA Registers Cylinder Low LBA 15-8 Register Address 1F4h174h Offset Feature Register Address 1F1h171h Offset 1, 0Dh Write OnlySector Count Register Address 1F2h172h Offset Sector Number LBA 7-0 Register Address 1F3h173h Offset TS8G~16GCF600 Device Control Register Address 3F6h376h Offset Eh Card Drive Address Register Address 3F7h377h Offset Fh Command Code CF-ATA Command Set Definitions Cyl High Cyl Low Sec Num Sec Cnt Feature Check Power Mode 98h or E5hExecute Drive Diagnostic 90h Bit Command Format Track 50h Transcend Information IncErase Sectors C0h Flush Cache E7h Bytes Drive Cyl High Cyl Low Sec Num Sec Cnt FeatureWord Default Total Data Field Type Information Identify Device Ech Ultra DMA Mode Supported and Selected PIO data transfer cycle timing modeCommand sets supported XXXXh Command sets enabled Key management schemes supported Word 0 General ConfigurationCF Advanced True IDE Timing Mode Capability and Setting CF Advanced PC Card I/O and Memory Timing Mode Capability Word 49 Capabilities Bit 13 Standby Timer Word 1 Default Number of CylindersWord 3 Default Number of Heads Word 6 Default Number of Sectors per Track Current Capacity Multiple Sector SettingTotal Sectors Addressable in LBA Mode Current Number of Cylinders, Heads, Sectors/Track Word 68 Minimum PIO transfer cycle time with Iordy Words 82-84 Features/command sets supportedRecommended Multiword DMA transfer cycle time Word 88 Ultra DMA Modes Supported and Selected Words 85-87 Features/command sets enabled Word 128 Security Status Bit 8 Security Level Word 91 Advanced power management level valueWord 89 Time required for Security erase unit completion Additional Requirements for CF Advanced Timing Modes Word 160 Power Requirement DescriptionValue Maximum PIO mode timing selected Value Maximum Multiword DMA timing mode supported Current Multiword DMA timing mode selected Value Current PIO timing mode selectedValue Maximum Pcmcia IO timing mode Supported Value Maximum Memory timing mode Supported Value PC Card Memory or I/O Udma timing mode Selected Value Maximum PC Card I/O Udma timing mode SupportedValue Maximum PC Card Memory Udma timing mode Supported Drive Cyl High Cyl Low Sec Num Sec Cnt Idle 97h or E3hIdle Immediate 95h or E1h Initialize Drive Parameters 91h Read DMA C8h Read Long Sector 22h or 23h NOP 00hRead Buffer E4h TS8G~16GCF600 Request Sense 03h Seek 7Xh Set Features EFh Feature Supported TS8G~16GCF600 Translate Sector Information Standby Immediate 94h or E0h Translate Sector 87h Wear Level F5h Write Buffer E8h Write DMA CAh TS8G~16GCF600 TS8G~16GCF600 NOP Error PostingBBK UNC Idnf Abrt Amnf Drdy DWF DSC Corr ERR S. Table Capacity Transcend Product Capacity CompactFlash Card Ordering Information