Manuals / Transition Networks / Computer Equipment / Network Card

Transition Networks CPSMC0810-100, CPSMC0800-100 manual DC Auxiliary Power Supply, power supply

Models: CPSMC0810-100 CPSMC0800-100

1 30

Download 30 pages 26.95 Kb

Page 15

3.2.2DC Auxiliary Power Supply

CPSMC08xx-100 PointSystem™ Chassis

3.2.2DC Auxiliary Power Supply

•This product is intended to be used in a restricted access location. Proper earthing (grounding) is required to ensure safe operation. Grounding terminals are provided (section 4.1.3) for proper grounding of the device as per customer installation requirements and local electrical codes. Prior to installation, use a voltmeter/ohmmeter to check the wiring for the presence of earth ground.

•A readily accessible disconnect device as part of the building installation shall be incorporated into the fixed wiring. The disconnect device (a 48 VDC, 15 or 20A circuit breaker or switch) must be included in the ungrounded supply conductor. Overcurrent protection must be a 48 VDC, 15 or 20A fuse or circuit breaker.

Read and follow all warning notices & instructions marked on the product or included in the manual.

CAUTION: All installation and service must be performed by qualified service personnel.

To power the CPSMC08xx-100 chassis through the DC auxiliary power supply:

1.Connect the female end of the external power converter to the auxiliary power inlet on the back of the chassis.

2.Connect the +48-VDC terminal to the connector marked “+”. Turn the terminal screw clockwise to secure.

3.Connect the -48-VDC terminal to the connector marked “-”. Turn the terminal screw clockwise to secure.

4.Connect the ground terminal to the connector marked “chassis ground”. Turn the terminal screw clockwise to secure.

5.Verify that Auxiliary power supply is connected properly by disconnecting the primary power supply, and then by observing the illuminated power LEDs on the installed slide-in-modules and by the chassis’ fan operation.

Auxiliary Power Inlet

External Power

Converter

power supply

GND – +

24 hour Technical Support: 1-800-260-1312-- International: 00-1-952-941-7600

15

Image 15

Transition Networks CPSMC0810-100 manual DC Auxiliary Power Supply, power supply, CPSMC08xx-100 PointSystem Chassis

Contents

revision B Transition Networks CPSMC08xx-100 8-Slot PointSystem ChassisUser’s Guide CPSMC0800-100 AC-powered CPSMC0810-100 DC-poweredCISPR22/EN55022 Class A + EN55024 CE Mark FCC Regulations CPSMC08xx-100 PointSystem ChassisCompliance Information 33270.B1 Introduction Table of Contents3 Powering the CPSMC08xx-100 6 Troubleshooting24 hour Technical Support 1-800-260-1312 -- International 1 Introduction1.1 Description CPSMC08xx-100 PointSystem ChassisPart Number 1.2 Unpacking the CPSMC08xx-100 Equipmentintroduction CPSMC08xx-100 PointSystem Chassis2.1.1 Chassis Face Plates 2.1.2 Calculating the Power Consumption2 Slide-in-Modules 2.1 Media Converter Slide-in-Modules24 hour Technical Support 1-800-260-1312 -- International 2.1.3 Installing the Media Converter Slide-in-Modulesslide-in-modules CPSMC08xx-100 PointSystem Chassis24 hour Technical Support 1-800-260-1312 -- International 2.2.4 Replacing the Media Converter Slide-in-Modulesslide-in-modules CPSMC08xx-100 PointSystem Chassismodules 2.2 Management Modulesslide-in 2.2.1 Three Types of Management Modules1a. CPSMM-200 Dual-Slot Master Management Module 2.2.2 Installing the Management Modulesslide-in-modules CPSMC08xx-100 PointSystem Chassis24 hour Technical Support 1-800-260-1312 -- International 2.2.3 Replacing the Management Modulesslide-in-modules CPSMC08xx-100 PointSystem ChassisCPSMC08xx-100 PointSystem Chassis 3 Powering the CPSMC08xx-1003.1 Primary Power Supply 3.1.1 AC Power Supply power supplyCPSMC08xx-100 PointSystem Chassis 3.1.2 DC Power Supplypower supply Power Terminal BlockInstant Fail Over Protection 3.2 Auxiliary Power Supply3.2.1 AC Auxiliary Power Supply AC and DC Power SuppliesCPSMC08xx-100 PointSystem Chassis 3.2.2 DC Auxiliary Power Supplypower supply Auxiliary Power Inlet External Power Converter4 CPSMC08xx-100 Chassis 4.1 Installing the CPSMC08xx-100 Chassis4.1.1 Table-Top Installation 4.1.2 Standard 19-inch Rack Installationchassis CPSMC08xx-100 PointSystem Chassis24 hour Technical Support 1-800-260-1312 -- International 24 hour Technical Support 1-800-260-1312 -- International 4.1.3 Grounding LugsCPSMC08xx-100 PointSystem Chassis chassis24 hour Technical Support 1-800-260-1312 -- International 4.2 Cascade Optionchassis CPSMC08xx-100 PointSystem Chassis24 hour Technical Support 1-800-260-1312 -- International chassisCPSMC08xx-100 PointSystem Chassis To cascade two or more CPSMC08xx-100 chassisCPSMC08xx-100 PointSystem Chassis 4.3 Connecting the Slide-in-Modules to the Network4.4 Operation LED indicators on the management module and slide-in-modulesCPSMC08xx-100 PointSystem Chassis 5 Network Management5.1 Hardware Connections network mgmtRESET CPSMC08xx-100 PointSystem Chassis DB-9 Serial PortRJ-45 Ethernet Port RESET24 hour Technical Support 1-800-260-1312 -- International 6 Troubleshootingtroubleshooting CPSMC08xx-100 PointSystem ChassisWarranty Technical SpecificationsAC Power Supply DC Power SupplyCPSMC08xx-100 PointSystem Chassis Cable SpecificationsNull Modem Cable RJ-45 Cable24 hour Technical Support 1-800-260-1312 -- International COAX CableCable Shield Grounding CPSMC08xx-100 PointSystem ChassisWeb-Based Seminars Contact UsTechnical Support Transition NowCSI Material Management Center c/o Transition Networks WarrantyLimited Lifetime Warranty CPSMC08xx-100 PointSystem ChassisCPSMC08xx-100 PointSystem Chassis Before making any non-warranty repair, Transition Networks requires a $200.00 charge plus actual shipping costs to and from the customer. If the repair is greater than $200.00, an estimate is issued to the customer for authorization of repair. If no authorization is obtained, or the product is deemed not repairable, Transition Networks will retain the $200.00 service charge and return the product to the customer not repaired. Non-warranted products that are repaired by Transition Networks for a fee will carry a 180-day limited warranty. All warranty claims are subject to the restrictions and conventions set forth by this document